38
PL
Instrukcja użytkowania
Struganie
Najpierw należy ustawić równo przednią dolną
podstawę struga na obrabianej powierzchni, unikając
kontaktu ostrza z materiałem.
Włączyć strug i zaczekać, póki narzędzie nie osiągnie
maksymalnej prędkości.
Ostrożnie posuwać strug do przodu. Zacząć struganie
naciskając na przednią część struga, zaś po
zakończeniu – na część tylną.
Struganie będzie łatwiejsze, jeśli ustawić część
obrabianą pod kątem. W ten sposób, podczas pracy
narzędzie będzie przesuwane w górę i w dół.
Od prędkości i głębokości cięcia zależy jakość
powierzchni. Strug wykonuje równe ścięcia z prędkością
obrotową zapobiegającą zaklinowywaniu w przypadku
obecności strużyn.
W przypadku strugania zgrubnego głębokość cięcia
można zwiększyć. Aby osiągnąć optymalną jakość
powierzchni, głębokość strugania należy zmniejszyć i
posuwać strug wolniej.
Zawrężanie [F3]
Do cięcia schodkowego użyć prowadnika równoległego
(8).
∙
Na elemencie obrabianym narysować linię cięcia.
Prowadnik równoległy (8) włożyć do otworu z przodu
narzędzia.
∙
Ustawić krawędź ostrza (20) względem
narysowanej linii cięcia.
∙
Wyregulować prowadnik równoległy (8), tak
by zetknął się z bokiem elementu obrabianego i
zabezpieczyć go, dokręcając śrubę (21).
Podczas strugania przesuwać narzędzie krawędzią
prowadnicy równo względem bocznej strony elementu
obrabianego. W przeciwnym razie efekt strugania może
być nierównomierny.
Ociosanie i skrzywianie krawędzi [F4]
Rowek w kształcie litery V (5) na podstawie przedniej
dolnej podstawy pozwala na skrzywianie (zaokrąglenie)
krawędzi części obrabianej.
∙
Rozmieścić 90° rowek w kształcie litery V na
krawędzi części obrabianej i posuwać się wzdłuż niego.
OBSŁUGA I PRZECHOWYWANIE
OSTROŻNIE! Przed rozpoczęciem
pracy z narzędziem należy odłączyć
go od gniazdka.
∙
Utrzymywać narzędzie i otwory wentylacyjne (o
ile są) w czystości. Regularne oczyszczanie i obsługa
gwarantują wysoką efektywność i długie użytkowanie
narzędzia.
∙
W przypadku zepsucia się, bez względu na
przestrzeganie wszystkich zasad użytkowania i
pobierania prób narzędzia, naprawa powinna być
dokonywana w oficjalnym centrum serwisowym IVT.
∙
Wszystkie nakrętki, śruby i wkręty powinny być
dokładnie dokręcone.
∙
Należy wymienić uszkodzone lub zużyte części.
∙
Używać tylko oryginalnych części zamiennych.
Części, wyprodukowane przez innych producentów,
niedokładnie przylegają i zwiększają ryzyko powstania
urazów.
∙
Przechowywać narzędzie w suchym niedostępnym
dla dzieci miejscu, w bezpiecznej odległości od
materiałów łatwopalnych.
∙
Unikać zachlapania narzędzia wodą!
∙
Należy regularnie ostrzyć ostrza i wymieniać
uszkodzone ostrza, Długotrwałe stosowanie tępych lub
zniszczonych ostrz obniża efektywność struga i może
spowodować obciążenie silnika.
∙
Aby uniknąć niewyważenia i wibracji zawsze należy
wymieniać (ostrzyć) obydwa ostrza jednocześnie.
∙
Zabrania się pracy z jednym ostrzem.
∙
Stosować tylko takie ostrza, które są dostarczane
w zestawie z narzędziem lub które można nabyć w
zautoryzowanych sklepach IVT.
Wymiana ostrzy [F5]
UWAGA! Rozmiary i waga nowego
ostrza
muszą
odpowiadać
parametrom wymienianego ostrza;
w przeciwnym przypadku wrzeciono
będzie wibrować, jakość strugania
obniży się, zaś narzędzie może zostać
uszkodzone.
∙
Wymontować ostrze (10) – jeśli urządzenie było
używane – należy ostrożnie oczyścić powierzchnie
bębna (11) oraz płytkę bębna (12). Aby wymontować
ostrza (10) z bębna (11), odkręcić śruby z użyciem
klucza nasadowego (25). Płytka bębna (12) wymontuje
się wraz z ostrzami (10).
∙
Aby zainstalować ostrza (10), z użyciem śrub z
łbem stożkowym ściętym (9) luźno przymocować płytkę
regulacyjną (13) do płytki ustalającej (14) i ustawić
ostrza (10) na podstawie płytki wzorcowej (19), tak by
krawędzie tnące ostrza były równo ustawione względem
wnętrza bocznej strony płytki wzorcowej (18).
∙
Ustawić płytkę regulacyjną (13) / płytkę ustalającą
(14) na podstawie płytki wzorcowej (19), tak by występy
ustalające ostrza (15) płytki ustalającej (14) znalazły
się w rowku ostrza. Następnie nacisnąć krawędź płytki
regulacyjnej (13), wyrównując tylną stronę postawy
Summary of Contents for PL-560-RC
