39
PL
Instrukcja użytkowania
płytki wyrównującej (19), i dokręcić śruby z łbem
stożkowym ściętym (9).
Ważne jest, by ostrze (10) było równo osadzone
względem wewnętrznego boku płytki wzorcowej
(18), występy ustalające ostrza (15) były osadzone w
rowku ostrza, a krawędź płytki regulacyjnej (13) była
usytuowana równo względem bocznej strony podstawy
płytki wzorcowej (19). Należy dokładnie sprawdzić,
czy elementy te są dobrze ustawione, tak by zapewnić
równomierne cięcie.
∙
Wsunąć krawędź płytki ustalającej (13) do rowka
bębna (11).
∙
Ustawić płytkę bębna (12) nad płytką regulacyjną
(13) / płytkę ustalającą (14) i przykręcić śruby z łbem
sześciokątnym, tak by między bębnem (11) a płytką
ustalającą (14) było wystarczająco przestrzeni na
wsunięcie ostrza (10) na jego położenie. Ostrze (10)
ustawia się w jego położeniu za pomocą wypustów
ustalających ostrza (15) na płytce ustalającej (14).
Regulację
wzdłużną
ostrza
należy
ręcznie
przeprowadzić, tak by końce ostrza znajdowały się w
jednakowej odległości od obudowy oraz metalowego
wspornika.
∙
Dokręcić śruby z łbem sześciokątnym i obrócić
bęben (11), sprawdzając odstępy pomiędzy końcami
ostrza a korpusem narzędzia.
∙
Sprawdzić, czy śruby z łbem sześciokątnym są
dobrze dokręcone.
Ostrzenie ostrzy (10) [F6]
Aby zapewnić najlepsze wyniki pracy, ostrza (10) muszą
być zawsze dobrze naostrzone. Z użyciem uchwytu
do ostrzenia (23) usunąć wyszczerbienia i wygładzić
krawędzie.
Należy wpierw odkręcić nakrętkę motylkową znajdującą
się na uchwycie do ostrzenia (23) i wsunąć ostrza
(10), tak by przylegały do boków. Dokręcić nakrętki
motylkowe. Przed rozpoczęciem ostrzenia zamoczyć
kamień do ostrzenia w wodzie na 2-3 minuty. Uchwyt do
ostrzenia (23) ustawić tak, by oba ostrza (10) dotykały
kamienia do ostrzenia. Dzięki takiemu ustawieniu oba
ostrza będą ostrzone pod tym samym kątem.
OCHRONA ŚRODOWISKA NATURALNEGO
Oddawajcie śmieci i odpadki do
przeróbki!
Narzędzie, urządzenia dodatkowe i opakowanie
należy odesłać do bezpiecznej z ekologicznego punktu
widzenia przeróbki.
Elementy plastykowe są oznaczone adnotacją o
możliwości klasyfikowanej przeróbki. Niniejsza instrukcja
została wydrukowana na papierze makulaturowym, nie
zawierającym chloru.
UWAGA! NIE NALEŻY DOKONYWAC PRÓB SAMODZIELNEJ NAPRAWY PRODUKTU
ANI PRZY NIM MANIPULOWAĆ! Wszelkie działania dotyczące naprawy lub dodatkowej
konserwacji muszą przeprowadzać wykwalifikowani i autoryzowani pracownicy centrum
usługowego IVT. Nie należy dokonywać prób modyfikacji żadnych wewnętrznych części
produktu! CZYNNOSC TAKA SPOWODUJE CAŁKOWITE UNIEWAŻNIENIE GWARANCJI, A
TAKŻE MOŻE DOPROWADZIC DO POWAŻNEGO USZKODZENIA CIAŁA LUB PRODUKTU.
Summary of Contents for PL-560-RC
