7
6
Manual instruction |
Rotary Hammer
EN
children
WARNING: use proper extention cord!
Use only proper extension cords that
accept the tool’s plug. Make sure your
extension cord is in good condition. Replace or
repair damaged or worn cord immediately. When
using an extension cord, be sure to use one heavy
enough to carry the current your product will
draw. An undersized cord will cause a drop in line
voltage resulting in loss of power and
overheating.
Auxiliary handle / Depth stop
For all work with the machine, the auxiliary handle
(4) must be mounted.
You will be able to obtain a safe body position when
working by rotating the handle attachement. Loosen
and turn the handle attachement in anticlockwise
direction. Then tighten the handle attachement.
(RHM-900 – RHM-1100)
The drilling depth can be set by using the depth
gauge (8):
loosen the clamp by unscrewing the auxiliary
1.
handle (4)
set the desired drilling depth
2.
Tighten the auxiliary handle (4)
3.
(RHM-1500)
After the auxiliary handle (4) is installed, slide the
depth gauge (8) to the desired depth and securely
tighten the wing knob (18).
Replacing tools
Clean tools and grease with a thin layer of machine
grease before fitting.
(RHM-900 – RHM-1100)
Fitting
pull back the fastening
1.
sleeve (5) and hold
push and rotate the
2.
tool into the tool holder as
far as it will go; the tool will
lock automatically
Check that it is locked
3.
by pulling the tool
Changing
Pull back the fastening
1.
sleeve (5), hold and remove
the tool.
(RHM-1500)
Fitting
Insert the accessory
1.
into the tool holder (5) through the dust guard (7),
while twisting and pushing inward until it locks
automatically
into
place.
Pull outward on
2.
the accessory to be
certain it is locked into
the tool holder.
Changing
Accessories may be hot after use. Avoid contact
1.
with skin and use
proper
protective
gloves or cloth to
remove. To remove
an accessory, pull
and hold the locking
sleeve backward and
pull bit forward. All
accessories should be wiped clean after removing.
NOTE:
The high efficiency available from the
rotary hammers can only be obtained if sharp and
undamaged accessories are used.
Initial operation
Always use the correct supply voltage:
the power
supply voltage must match the information quoted
on the tool identification plate.
Switching On/Off
Switching On: press the On/
Off trigger switch (1)
Switching Off: release the On/
Off trigger switch (1)
Speed selection
(RHM-1100 – RHM-1500)
With the speed selector thumbwheel (12) the
Summary of Contents for RHM-1100
