background image

GridBee GS Mixers. 

The GridBee Series GS mixers are warranted to be free of defective parts,

materials, and workmanship for a period of five years from the date of purchase. This warranty is valid 

only for use of the equipment in accordance with the owner’s manual and any initial and ongoing

factory recommendations. This warranty is limited to the repair or replacement of defective components 

only and does not apply to normal wear and tear.  If the factory’s service crews performed the original 

on-site placement and startup, then this warranty also includes labor.  Where labor is included, in lieu of 

sending a factory service crew to the site for minor repairs, Ixom may choose to send the replacement 

parts to the owner postage-paid and may pay the owner a reasonable labor allowance, as determined 

solely by Ixom, to install the parts.   There is no liability for consequential damages of any type.  The 

warranty that is submitted and provided with the purchased equipment is the valid warranty. 

GridBee control panels, cold weather hose kits, air compressors and any optional accessories. 

These items are considered “buyout” items for Ixom, and as such include a warranty against defects in 

material and workmanship for one year from the date of purchase.  This warranty covers parts only, not 

labor.  Parts that are determined by Ixom to be defective in material or workmanship under normal use 

during the one year warranty period will be repaired or replaced.  Shipping charges are the

responsibility of the customer.  

Terms applicable to all equipment.   

This Limited Replacement Warranty is subject to the terms of 

Ixom’s General Terms and Conditions of Sale.  In the event of any inconsistency between the terms of 

this Limited Replacement Warranty and Ixom’s General Terms and Conditions of Sale, the terms of this 

Limited Replacement Warranty shall prevail to the extent of that inconsistency.

© 2020 Ixom | www.medoraco.com | 866 - 437 - 8076 | info@medoraco.com

Warranty

GridBee GS Submersible Mixer Limited Replacement Warranty

1684_10018_20200420

O&M_GS12_120V_1PH_10025_20200811 - 16

Summary of Contents for MEDORA GridBee GS-12




















Reviews: