background image

Suspended Configuration

GS Series

Cord ran through 

penetration fitting 

and cord seal.

Chain and Kellum 

Grip attached to 

quick link on 

penetration fitting

Mixer suspended 

near tank floor

Chain Connected 

to Mixer

Suspended Configuration

The suspended configuration is primarily used 

on tanks without a flat bottom. This method of 

installation is different with aluminum roofs or 

geodesic domed roofs. 

Installation Procedures

 

Step 1:

Attach the retrieval chain to the GS mixer at the 

pre-located quick link. Tighten the quick link with 

a wrench/pliers. Plan out a safe procedure and 

hoist the GS Mixer to the top of the tank near the 

hatch opening. Use the chain and submersible 

cable attached to the GS Mixer for lifting and 

supporting the weight. Keep clear of chain and 

electric cord to avoid entanglement.

Step 2:

Tie off the tail end of the retrieval chain and 

electric cord strain relief to the quick link at the 

bottom of the tank penetration fitting. 

Step 4:

 

Pull the retrieval chain up until it is taught, then 

mark off the desired distance the GS Mixer is to 

be suspended above the floor, placing the quick 

link that desired distance down the retrieval 

chain below the tank penetration fitting.

Step 5:

Slowly pull up the GS Mixer and connect the 

quick link to the tank penetration fitting.

IMPORTANT

It is important to disinfect all components in

contact with potable water. A common practice is to 

use a minimum 200ppm chlorine or alternate dis-

infectant solution in water to spray all components 

that will contact the drinking water. There may be 

additional  decontamination  procedures  required, 

so  it  is  important  to  understand  what  procedures 

are  acceptable.    Decontamination  should  be  per-

formed right before the unit is lowered through the 

hatch.  The  mixer  should  be  immersed  in  water 

shortly  after  having  been  decontaminated  to  pre-

vent corrosion caused by contact with chlorine or 

alternate disinfectant.

© 2020 Ixom | www.medoraco.com | 866 - 437 - 8076 | info@medoraco.com

Placement

1916_10006_20200514

O&M_GS9_10012_20200811 - 10

Summary of Contents for Medora GridBee GS-9




















Reviews: