background image

GridBee SN Spray Units.  

GridBee SN Spray Units and blowers are warranted to be free of defective 

parts, materials, and workmanship for a period of two years from the date of purchase. The optional 

control panels, by other manufactures, are covered by a manufacturer’s warranty of one year from 

date of purchase. This warranty is valid only for use of the GridBee THM Removal System in

accordance with the owner’s manual and any initial and ongoing factory recommendations. This

warranty is limited to the repair or replacement of defective components only and does not apply to 

normal wear and tear.  If the factory’s service crews performed the original on-site placement and 

startup, then this warranty also includes labor.  Where labor is included, in lieu of sending a factory 

service crew to the site for minor repairs, Ixom may choose to send the replacement parts to the 

owner postage-paid and may pay the owner a reasonable labor allowance, as determined solely by 

Ixom, to install the parts.   There is no liability for consequential damages of any type.  The warranty 

that is submitted and provided with the purchased equipment is the valid warranty. 

GridBee control panels, and any optional accessories.  

These items are considered “buyout” 

items for Ixom, and as such include a warranty against defects in material and workmanship for one 

year from the date of purchase.  This warranty covers parts only, not labor.  Parts that are determined 

by Ixom to be defective in material or workmanship under normal use during the one year warranty 

period will be repaired or replaced.  Shipping charges are the responsibility of the customer.  

Terms applicable to all equipment.  

This Limited Replacement Warranty is subject to the terms of 

Ixom’s General Terms and Conditions of Sale.  In the event of any inconsistency between the terms 

of this Limited Replacement Warranty and Ixom’s General Terms and Conditions of Sale, the terms of 

this Limited Replacement Warranty shall prevail to the extent of that inconsistency.

© 2020 Ixom | www.medoraco.com | 866 - 437 - 8076 | info@medoraco.com

Warranty

GridBee THM Removal Systems Limited Replacement Warranty

1683_10035_20200420

O&M_SN10_10030_10104_20201006 - 13

Summary of Contents for Medora GridBee SN10

















Reviews: