background image

31 

November 5, 2015 

 

 

 
 

 
 
 
 
 
 

J. A. Roby Limited Lifetime warranty 

WOOD BURNING STOVES & FIREPLACES 

J. A. ROBY’s warranty only applies to original buyer and is non-transferable. This warranty covers brand new products only, which have not 
been altered, modified nor repaired since shipment from factory. The products covered by this warranty must be manufactured after the review 
date indicated at the bottom of page. Proof of purchase (dated bill of sale), model name and serial number must be supplied when making any 
warranty claim to your J. A. ROBY dealer. Registering your warranty is not required. 

The appliance must be installed by an authorized service technician or contractor. Installation must be done in accordance with the installation 
instructions included with the product and all local and national building and fire codes. Any service call related to an improper installation is 
not covered by this warranty. This warranty applies to normal residential use only. This limited warranty does not cover damages caused by 
misuse, improper installation, lack of maintenance, accident during transportation, alterations, power failure, venting problems, downdrafts, 
abuse, over firing or neglect. Operating the appliance on high for extended periods of time is considered as a neglect. Any defect or damage 
caused by the use of unauthorized parts or other than original parts void this warranty. 

This limited warranty does not cover any scratch, corrosion, warping or discoloration. The manufacturer may require that defective products 
be returned and/or that digital pictures be provided to support the claim. Returned products are to be shipped prepaid to the manufacturer for 
investigation. If a product is found to be defective, the manufacturer will repair or replace such defect. The transportation fees to ship back the 
product to the purchaser will be paid by the manufacturer

2

. The external labour fees related to warranty repair are not covered. The manufacturer 

may, at its discretion, decide to repair or replace any part or unit after inspection and investigation of the defect. The manufacturer may, at its 
discretion, fully discharge all obligations with respect to this warranty by refunding to the original warranted purchaser the wholesale price of 
any warranted but defective part (s). The manufacturer shall not in no event be liable for any special, indirect or consequential damages of any 
nature whatsoever which exceeds the original purchase price of the product. All parts replaced under this limited lifetime warranty are subject 
to a single claim. 

Any  damage  to  the  appliance,  combustion  chamber,  heat  exchanger,  enameled  cast  iron  cooking  plate  or  other  components  due  to  water, 
weather damage, long periods of dampness, condensation, damaging chemical or cleaner will not be the responsibility of J. A. ROBY. Failure 
of  any components which is attributed to poor maintenance, is not  warrantable and will not be covered  by this policy.  J.A. ROBY neither 
assumes, nor authorizes any third party to assume, on its behalf, any other liabilities with respect to the sale of this product. 

The manufacture of your new appliance and the following materials are warranted against defects as mentioned below:  

WARRANTY DESCRIPTION 

100% 

50% current retail price 

Ashtray, handles, doors and cast iron legs 

Life 

 

Combustion chamber 

5 years 

From 5 years to life 

Secondary air tubes 

5 years 

 

Heat exchanger 

2 years 

From 2 years to life 

Switches,  Snap  Disc,  wiring  and  electrical  components,  standard  blowers  and 
rheostat 

2 years 

 

Tempered glass, optional blower and gasketing 

1 year 

 

Ceramic glass (thermal breakage only

1

1 year 

 

Replacement parts (with proof of purchase) 

90 days 

 

Due to on-doing product improvements, all specifications and design are subject to change without prior notice

.

 

Before shipping your unit or defective component to our plant, you must obtain an authorization number from J. A. ROBY dealer. 
Any merchandise shipped to our plant without authorization will be refused automatically and returned to sender.  

 

1

= Digital pictures required       

2

= Shipping cost are not covered outside CANADA 

Review Oct. 2014 

STOVES & FIREPLACES 

Summary of Contents for ROBY2500 CUISINIERE
































Reviews: