background image

REV 6-11-2019 

IMPORTANT SAFETY INSTRUCTIONS 

 

When using an electrical appliance, basic precautions should always be followed, including the following: 

 

READ ALL INSTRUCTIONS BEFORE USING (THIS APPLIANCE) 

 

WARNING 

– To reduce the risk of fire, electric shock, or injury:

 

Do not use on wet surfaces. 

Use only as described in manual. Use only manufactures recommended attachments. 

Do not allow to be used as a toy. Close attention is necessary when used by or near children. 

Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair and anything that 
may reduce air flow. 

Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts. 

Do not use to pick up flammable or combustible liquids, such as gasoline, or use in areas where they may be present. 

Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes. 

Do not use without dust bag and/or filters in place.

 

 

SAVE THESE INSTRUCTIONS 

 

Installation Instructions:

 

Determine location to mount unit (

“DANGER”  “THIS EQUIPMENT INCORPORATES PARTS SUCH AS SWITCHES, 

MOTORS, OR THE LIKE THAT TEND TO PRODUCE ARCS OR SPARKS THAT CAN CAUSE AN EXPLOSION. WHEN 
LOCATED IN GASOLINE-DISPENSING AND SERVICE STATIONS INSTALL AND USE AT LEAST 20 FEET (6 M) 
HORIZONTALLY FROM THE EXTERIOR ENCLOSURE OF ANY DISPENSING PUMP AND AT LEAST 18 INCHES (450 

MM) ABOVE A DRIVEWAY OR GROUND LEVEL.”

 

Run electrical service to that location 

(NOTE UNIT HAS WIRE PROVIDED UNDERNEATH TO CONNECT INCOMING 

POWER SUPPLY)

 

Grounding Instructions

: This appliance must be connected to a grounded metal, permanent wiring system; or an 

equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal 
or lead on the appliance. 

Circuit must be protected by GFCI device. 

All local and national electric codes must be followed for installation and use. 

Licensed electricians are recommended for installation. 
 

Summary of Contents for 9217






















Reviews: