J.E. Adams 9420-1G-DIG Owner'S Manual Download | Manualshive

Page: 4 / 12

background image



Once unit has been installed use 5871B8 cap plugs supplied with unit to

seal holes in canister bottom located in lower cleanout door. Then connect
to power.



Turn unit on and move to programming instructions.

Programming Instructions:

Coin acceptor:



Comes standard with manual Imonex coin mech. no programming
needed.

Bill acceptor:



Bill acceptor comes pre programmed from J.E. Adams and should not

require any changes. If additional programming is needed to acceptors
please refer to additional literature sent along with this unit.

3/30/2011

4

«
...
2
3
4
5
6
...
»

Summary of Contents for 9420-1G-DIG













Reviews:

No comments

Related manuals for 9420-1G-DIG

Brand: b-mola Pages: 9

Brand: Fellowes Pages: 32

Brand: Kärcher Pages: 126

Brand: Kärcher Pages: 160

Brand: Kärcher Pages: 14

Brand: Kärcher Pages: 13

Brand: Kärcher Pages: 44

Brand: Kärcher Pages: 15

PrecisionAire 225T Series

Brand: Flanders Pages: 5

Brand: Tekno Pages: 8

Self-Propelled WindTunnel Cleaner

Brand: Hoover Pages: 16

Brand: XPOtool Pages: 8

Brand: WELLTEC Pages: 43

Brand: Bionaire Pages: 2

Brand: H-P Products Pages: 12

Solaris Twix 5500.0 HQ

Brand: Zelmer Pages: 58

Brand: DreameTech Pages: 76

H2O HD KB-019-1

Brand: Thane Fitness Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands