background image

http://www.jperkinsdistribution.co.uk

SPECIFICATIONS

Main rotor diameter ........................................520 mm

Fuselage length................................................500 mm

Radio control ............................................... 4-channel

(with 2 micro servos, speed controllers, piezo gyro)

Flying weight..........................................................300g

CONTENTS

Assembled helicopter (incl. main & tail motors) ... 1

4 ch 35Mhz FM transmitter (incl. trainer switch)... 1

“4 in1” on-board electronics unit

(6 channel receiver, piezo gyro, electronic mixers 

and speed controllers)............................................... 1

Micro servos................................................................ 2

Transmitter and receiver crystals .................... 1 pair

8.4V 600 mAh Ni-Mh battery pack............................ 1

Mains charger (220V UK 3-pin type)........................ 1

Trainer cable................................................................ 1

Instructional DVD (showing Mode 1 setup) ........... 1

Transmitter instruction manual................................. 1

Twister instruction manual........................................ 1

FEATURES

  Factory-assembled, RC installed COMPLETELY 

READY-TO-FLY micro RC helicopter

  One-piece '4 in 1' on-board computerised 

electronics unit saves weight, improves 

performance and simplifies use

  Transmitter with buddy box training switch and 

charging socket with adjustable height sticks 

and silky smooth operation

  Trainer lead AND instructional DVD included

  Speed controller disallows high throttle starts

  Throttle Fail-safe cuts in when signal lost 

  Gyro is disabled at closed throttle to prevent 

unexpected tail rotor starts during transport

  Ball bearing swashplate, rotor head, main shaft 

and tail shaft for ultimate precision

  Carbon fibre boom, UC struts, flybar, etc

  Rechargeable 8.4V Nimh battery 

  Around 10 minutes flying per charge

  UK 3-pin 240V mains flight charger

  Only requires 8 AA alkaline cells

  Ideal for newcomers to R/C 

  Upgradeable to collective pitch

Includes 3-

pin charger, 

Nimh 

rechargeable 

and 'Buddy 

box' trainer 

cable

Learn to fly 

R/C helicopters 

with the 

completely 

assembled 

Twister

–includes 

35FM precision 

transmitter 

with all 

equipment 

factory-fitted 

AND test-flown

EVERY TWISTER IS 

FLIGHT-GUARANTEED!

EVERY TWISTER IS 

TEST-FLOWN!

FREE 

Instructional DVD 

FREE 

Flight Training Guide

FREE 

'Buddy Box' trainer cable

 

COMPLETELY

READY TO FLY!

 

ASSEMBLED!

READY-BUILT MINI R/C HELICOPTER WITH 4-CHANNEL R/C

INCLUDING 'BUDDY BOX' FLIGHT TRAINING SYSTEM WITH PUPIL TRAINER CABLE

4-in-1 unit

Summary of Contents for Twister













Reviews: