background image

WARRANTY AND RETURNS POLICY

J-Tech warrants all products manufactured by J-Tech, 

to be free from defects in material and workmanship for a period of one (1)

year from date of shipment. Products or parts must be properly installed and used under normal conditions. Any product which
has been altered, including modification, misuse, accident, natural disaster, acts of nature, or lack of maintenance will not be
considered under warranty. Normal wear is excluded. The sole responsibility of J-Tech under this warranty is limited to repairing
or replacing any part or parts which are returned, prepaid by customer, and are found to be defective by J-Tech. Authorization
from J-Tech must be obtained before returning any part. All RMA (Return Merchandise Authorization) numbers expire 30 days
after initial issue date. J-Tech will not be liable for transportation expenses; nor for loss of profits or use; nor for incidental, special
or consequential damages of any kind. J-Tech makes no warranties with respect to component parts or accessories not
manufactured by J-Tech, same being subject only to such warranties, if any, as may be made by their respective manufacturers.
Use of nonauthorized replacement parts on any product not purchased through J-Tech or repair not completed by J-Tech shall
void this warranty.

Seller expressly disclaims and buyer expressly waives any other warranties, written, oral, statutory, express, implied, or otherwise, including, but not limited to,
merchantability, fitness for a particular purpose, or warranties to consumers under federal law. There are no warranties which extend beyond those described
herein. The liability of seller to buyer arising out of the sale of products or their use, whether such liability be asserted on warranty, contract, tort, negligence,
strict liability or any other basis, shall not in any case exceed the cost of repair or replacement of the products, as provided herein, and upon expiration of the
one-year period described above. All such liability shall terminate, and buyer waives any claim, therefore. It is understood and agreed that the foregoing shall
constitute the sole remedy of buyer.

Summary of Contents for LANEBLADE




























Reviews: