background image

J/105   Owner   Guide

   ......................................................................................................................................................................................................................................................      

14   

Tuning   the   J/105   Rig   

Following   is   a   general   guide   to   tuning   your   J/105   mast.      Please   consult   your   sailmaker   for   “fine-­‐
tuning”   the   mast   to   match   the   sails.   

With   the   standard   length   J/105   headstay   and   the   mast   step   situated   in   the   middle,   the   mast   rake   
(as   measured   from   the   back   of   the   mast   at   deck   level   to   a   plumb   on   the   main   halyard)   should   be   
approximately   30   inches.         Several   owners   have   opted   to   install   an   additional   toggle   at   the   top   of   
the   headstay,   and   then   shorten   the   drum   turnbuckle   so   to   lower   the   drum   as   close   as   possible   to   
the   deck.         According   to   J/105   Class   Rule   7.4   “the   headstay   system   length,   measured   between   the   
centerline   of   the   headstay   pin   on   the   mast   to   the   intersection   of   the   stem   line   and   the   sheer   line   
at   the   bow,   shall   not   be   greater   than   13035mm   nor   less   than   12985mm.   We   recommend   the   
maximum   allowed   headstay   length   for   most   conditions.         

The   upper   shrouds   are   attached   to   the   outer   chainplate   hole.      The   lowers   are   connected   to   the   
inner   hole.      The   intermediates   are   secured   in   the   forward   hole.      Begin   by   hand   tightening   the   
shrouds,   being   careful   to   keep   the   mast   centered   aloft.      Check   alignment   by   hoisting   a   tape   
measure   up   the   main   halyard   and   comparing   measurements   to   the   port   and   starboard   
chainplates.      When   the   top   of   the   mast   is   centered,   sight   up   the   mast   track   to   check   for   alignment   
of   the   lower   part   of   the   mast.      Hand   adjust   the   shrouds   as   necessary   to   center   the   mast.   

After   the   rig   is   centered   and   hand   tight,   we   recommend   additionally   tightening   the   shrouds   the   
following   number   of   turns:   

   

      Upper   Shrouds:      +11   turns   

      Lower   Shrouds:      +   2   turns   

      Intermediates:               +   8   turns   

   

You’ll   find   it   easiest   to   tighten   the   upper   shrouds   if   you   pump   the   backstay   down   2-­‐3   inches   first   
to   relieve   load.         Under   sail,   it   is   easiest   to   adjust   only   the   leeward   shrouds,   then   tack   to   adjust   the   
other   side.   

Once   you   have   initially   tuned   your   J/105,   then   go   sailing   in   a   brisk   breeze,   spending   equal   time   
on   both   tacks.      Even   though   rod   rigging   is   the   lowest   stretch   material   possible,   you’ll   still   see   a   
little   loosening   after   the   initial   breaking   in   period.         Be   sure   to   sight   up   the   mast   while   it   is   under   
load   to   see   if   it   remains   in   column.   

   

   

      

   

   

Summary of Contents for 105





















































Reviews: