The JA-159P wireless outdoor PIR detector
The JA-159P wireless outdoor PIR detector
2 / 2
MMY51801
Fig. 5.
The detection area angle is 90°. The direction can be adjusted
from position A – G by rotating the detector´s plastic part. Each step
is circumscribed. The detector lens covers the whole angle of 180° -
therefore it does not require any adjustment.
You can restrict the detection angle by adhesive masking
strips supplied with the package. This way you can eliminate
problematic parts of the detection area. The strips are to be
stuck on the relevant lens segment from the inner side.
The PIR detection sensitivity can be configured by a 3-pole switch
located under the upper sensor. The letters correspond to sensitivity
levels as follows:
L
low – applicable to bad conditions
M
middle
H
high
Other parameters can be configured using a DIP switch:
NORM
TEST
120s
5s
5 s … šet
Ĝ
ící režim
N.C.
N.O.
LED OFF
LED ON
on
Antimasking OFF
Antimasking ON
Factory settings highlighted by bold letters.
The LED serves for PIR detector testing – checking the coverage.
The detector always sends information to the control panel. For
normal detector operation the LED should be turned off in order to
save the battery.
The power save mode can be set up by DIP switch no. 2, select
5 s / 120 s.
Testing (coverage test)
By DIP switch no. 1, enter test mode and by DIP switch no. 4 turn
on the LED indication. Close the detector. Test the detection range
of the protected area and immunity out of the protected area.
Bear in mind the potential changing of detecting distance
influenced by the environment.
Each movement is indicated by LED and it sends the information to
the control panel (can be checked by F-link software in the
Diagnostics tab).
We recommend turning off the indication LED when the testing
procedure is finished. And set up the power save mode to 120s to
get a longer battery lifetime.
Normal operating mode
The detector sends a radio signal about activation when it is
triggered. In the case of tampering with the detector or tearing the
detector off its position the detector sends a tamper signal. Every 9
minutes status report is sent to the control panel.
Replacing the batteries
The detector checks its battery status automatically and if the
batteries are running low it informs the system. The detector remains
fully functional. The batteries should be changed as soon as possible
(within 1 week).
Before battery replacement
the control panel has to be switched
to service mode (see installation manual of the control panel) and
then it is possible to open the cover of the detector. Always use
CR123A (3V, 1500 mAh) batteries or alternatively LS(T) 14500 (3,6V
AA) batteries.
Note
: Always use 2x lithium batteries. If needed put 3x batteries in
to increase the detector’s lifetime.
Troubleshooting
Problem
Problem cause
Solution
The detector
makes false
intrusion
alarms
Lower detection area is
unnecessarily long.
Set the detection area
properly.
The detector is exposed
to direct/reflected light
(sun light, car light etc.).
Remove the reflector,
mask the area exposed to
the reflection of light or
change the detector
position.
There is a moving object
in the area (laundry on
the clothes-line, plants
etc.).
Remove the moving
object or change the
detector position. Or put
the stickers on part of the
lens to avoid detection in
a problematical place.
Occasionally
no reaction
to
movement
Lower detection area is
unnecessarily short
Set the detection area
properly
Sensitivity is set to low
(L).
Change sensitivity to
medium (M) or high (H).
The detector is in battery-
save mode
While testing operation,
set the battery-save timer
to 5 seconds.
Detector
ignores any
movements
Low battery
Replace the battery
LED indicator lights but
there is no reaction in the
control panel.
The control panel is out of
range, check the battery,
try to reposition detector
or control panel
Fig. 6. Detector dimensions (mm)
Technical specifications
Power:
2x Lithium battery CR123A (3 V, 1500mAh)
Average battery lifetime
2 x (3 x) CR123A, approx. 3 years (4 years)*
Alternative power
2 x Lithium battery LS(T)14500 (3.6 V,AA)
Average battery lifetime
2 x (3 x) LS(T) 14500, approx. 3 years (4years)*
*-valid for enabled 120s saving mode
Communication band
868.1 MHz
RF range – communication range
up to 300 m (open area)
Optex detector parameter
Detection characteristics
12 m / 90 °; 16 segments
Recommended installation height
0.8 – 1.2 m
Object motion speed
0.3 – 1.5 ms
-1
Battery saving timer
adjustable 5 s or 120 s
Operational environment according to EN 50131-1
IV
Security grade
according to Optex
Operating temperature range
-20 °C to +60 °C
Detector cover conformance
IP55
Max. relative humidity of the environment
95 %
Dimensions
186 x 71.3 x 105.5 mm
Weight 500
g
Complies with
ETSI EN 300 220, EN 50130-4,
EN 55022, EN 60950-1, EN 50581
Can be operated according to
ERC RED 70-03
JABLOTRON ALARMS a.s. hereby declares that the
JA-159P
is
in compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC and 2011/65/EU. The original
of the conformity assessment can be found at
www.jablotron.com
- Technical Support section
.
Note: Although this product does not contain any harmful
materials we suggest you return the product to the dealer or
directly to the producer after use. For more detailed
information visit www.jablotron.com.
