7
EN
MFV52116_A
Important information:
The device uses a highly sensitive sensor to detect breathing. Its operation can be affected by shakes of
the crib, fl oor or the whole building especially in the home health care environment. This is why the crib
must not touch a bed in which somebody is sleeping or other equipment that vibrates. Interfering shocks
can also be caused by intensive air circulation (fans, air conditioning, etc.), people walking near the crib and
other factors. If you move the crib to a new place or if you turn on a new appliance that generates mechani-
cal vibrations or electromagnetic interference, we recommend that you test the device’s functioning. Wire-
less communication technology devices such as wireless home networks, mobile phones, cordless phones
and their base stations, mobile stations, which may adversely affect the baby and affect the functionality
and usability of the BM-02 should not be used closer than 1 m, nor should amateur radio equipment be
closer than 10 m from any part of the BM-02. Interferences can prevent the BM-02 from monitoring the
infant‘s breathing. Therefore we always recommend you to test the device functions before use.
You should avoid using mattresses made of hard materials (foam polystyrene, etc.) that absorb disturbing
vibrations caused by the movement of the ambient air.
Bear in mind that the device can only warn you in the case of an emergency but that it does not prevent
the risk of a breathing stoppage! If the baby has any physical problem, it is up to you or your doctor to
provide appropriate help. Do not stay too far from your baby to make sure that you hear the alarm, should
it go off, and that you are able to respond.
The manufacturer is responsible for the functionality of the BM-02 provided it is installed and used in
accordance with this manual. The manufacturer waives any responsibility for the proper functionality of
the product in the event that it is mechanically or otherwise damaged or for battery defects. Moreover,
the manufacturer waives any responsibility in the event that the product has been used in contradiction
to this user manual or the service life of the product has been exceeded.
The manufacturer urges you not to purchase a used product or to get it from a rental store. Rough han-
dling may reduce the sensitivity of the sensor, which may have its consequences. Should this be the case
the manufacturer waives all responsibility for the functionality of the product.
BATTERY REPLACEMENT
The device checks its battery status. When the batteries are running low, necessary replacement is signaled
by the indicator with the battery symbol fl ickering red. Also, the device does not confi rm the activation of the
switch when the batteries are discharged. Turn off the device before replacing the batteries. Remove the ba-
ttery compartment cover (see the Installation Instructions – page 4) and take out the original batteries.
Always use only new, branded alkaline AA LR6 batteries (the polarity is clearly marked in the battery
compartment). Once you have replaced the batteries, turn the device on briefl y – its activation must be con-
fi rmed by a beep. Do not use rechargeable batteries. When fi nished using the device, take the batteries out.
CLEANING AND MAINTENANCE
Besides battery replacement, the device does not require any special maintenance. We recommend that you
occasionally check the sensor pad in the crib to make sure that no moisture precipitates in the area where
the pad touches the mattress. You should turn the pad inside the crib by 180° once in a while, or turn it over
and air it. Clean the pad with a slightly moist cloth. (Do not use aggressive detergents.). Despite resistance
to foreign elements or liquids, their intrusion can damage the device. The product is supplied with an anti-
bacterial tissue for disinfecting the pad, if necessary. The frequency of cleaning does not affect the service
life of the product. Protect the sensor pad, supply cable and connector from mechanical damage (shocks,
sagging, tensile stress, etc.). If you detect any damage, contact the vendor or the manufacturer’s service
department directly (page 9).
Book 2016 - 16a.indb 7
Book 2016 - 16a.indb 7
11.4.2017 10:09:01
11.4.2017 10:09:01
Summary of Contents for Nanny BM-02
Page 1: ...baby breathing monitor...
Page 3: ...www jablotron com...
