background image

 
If the 

(

11.)

  parameter is disabled, any triggered detector is bypassed 

automatically – no key-press confirmation is needed. 
While setting (arming) the system via a key-fob controller, any triggered zone 
is bypassed automatically regardless of the 

(

11.)

 parameter. 

If a detector has been bypassed, it starts to protect as 
soon as it is de-triggered (for example, if a door is 
closed). 

3.  After the system has just been set (armed) 

 

The keypad 

beeps

  and an exit delay will begin. The keypad displays 

Exit delay

”. 

 

The keypad indicates which sections have been set (A; B; C). 

 

If exit delay acoustic signalling 

(

6.)

  is enabled, the exit delay is 

indicated by regular beeps from the keypad (the beeps get faster in the 
last 5 seconds). 

 

For a partially set system, the exit delay may not be signalled 
acoustically 

(

7.)

 

You have to leave protected areas before the exit delay 

(

20

)

 elapses.  

 

If 

final-door

  detector mode 

(

12.)

  is triggered during an exit delay, 

then the exit delay is extended to the moment when the final door is 
closed. So you can set and leave the house comfortably without any 
haste. If the final-door detector is not triggered, then the system 
provides a normal exit delay. 

 

4.   System unsetting (disarming) 

After you step into a set (armed) section, an 

entrance delay

 will begin. This is 

indicated by displaying “Entrance delay” on the keypad. Also, the keypad starts 
to beep fast if entrance delay acoustic signalling is enabled 

(

8.) 

(the wireless 

keypad only if it is powered from  the AC adaptor or the door detector is 
connected to the keypad or when you open its cover). Additionally, the 
entrance delay time can be indicated by an indoor siren. 
 

 

During the entrance delay 

(

 

21)

 you have to unset (disarm) the system 

by entering a valid access code (or, alternatively, presenting a valid 
access card, or using a valid key-fob). 

 

If final-door detector mode 

(

12.)

  is active and you came in through 

the corresponding door, then the entrance delay would be six times 
longer than if it had been triggered by an ordinary detector (i.e. if you 

 

Oasis user manual 

MKE22102

  

Summary of Contents for Oasis
























Reviews: