background image

Limited warranty 

 

Subject to the conditions of this Limited warranty Jablotron Ltd. warrants this 
product to be free from defects in design, material and workmanship at the time 
of its original purchase by a customer for a subsequent period of two (2) years. 
Should your Product need warranty service, please return it to the dealer from 
whom it was purchased. 

 

Conditions: 

1)

 

The warranty is valid only if the original receipt issued to the original 
purchaser by the dealer, specifying the date of purchase, is presented 
with the Product to be repaired or replaced. Jablotron reserves the 
right to refuse warranty service if this information has been removed 
or changed. 

2)

 

This warranty does not cover any failure of the Product due to misuse, 
including but not limited to  use in other than the normal and 
customary manner, in accordance with instructions for use and 
maintenance of the Product. Nor does this warranty cover any failure 
of the product due to accident, modification, adjustment, improper 
repair or acts of God. 

3)

 

This warranty does not apply to batteries nor modules of other 
suppliers (e.g. SIM card of the GSM provider). 

4)

 

The warranty provided does not affect the consumer's statutory rights 
under applicable national legislation in force, nor the consumer's rights 
against the dealer arising from their sales/purchase contract. 

  

Summary of Contents for Oasis
























Reviews: