TP-98TX Wireless Thermostat
1/2
MFR51405
Wireless Thermostat TP-98TX
This thermostat can replace a common indoor residential
thermostat and is designed to be used with electric, gas or oil
heating system. The easy to read display shows the current room
Temperature and temperature adjustment is very simple.
The TP-98TX wireless thermostat is compatible with Jablotron’s
wireless receivers UC-222, UC-241 and UC-242. Radio
communication provides high reliability and allows for very easy
installation as well.
25
5
.
INSTALLATION
The TP-98TX should be mounted in a dry indoor location. This
thermostat has been designed for easy installation. Choose a
mounting location about 1.5 meters above the floor, in an area with
good air circulation. Avoid places with drafts, dead air spots and
radiant heat from the sun or appliances. It should not be installed
close to any metal structure or other objects that may obstruct
radio signal transmissions.
•
Remove completely the front housing of the thermostat. (using
a screwdriver)
•
Drill two holes and insert the plastic dowels.
•
Attach the thermostat to the wall with the two screws.
ENROLLING THE TP-98TX INTO THE RECEIVER
•
Slide the battery cover upward to open it.
•
Remove the batteries from the thermostat if there are any.
•
Enter the enrolling mode of the receiver unit (UC-222, UC-241,
UC-242) – See corresponding instruction manual
•
Place the batteries into the thermostat. Ensure the correct
polarity of the batteries.
•
The receiver will confirm successful enrollment
•
Push and slide the cover down to close it.
Note: Each UC-222 receiver can work with only one thermostat.
If the receiver unit was used with any other device before, reset its
memory before enrolling a thermostat.
TEMPERATURE SETTING
In the normal operation mode, the thermostat shows the room
temperature. To set a desired temperature:
•
Press
or
button to view the previous temperature, which
was set last time.
•
Hold
or
button for about 3 seconds and the temperature
indicator will flash one time. Press
or
button to increase
or decrease the temperature setting. The unit will return to
normal operation mode automatically after 10 seconds with out
any button being pushed..
•
The programmed temperature range is from 5°C to 35°C.
The temperature span between the turn ON and OFF is 1°C. For
example, if the control temperature setting is 20°C, \the heater will
operate when the room temperature drops to 19.5°C and will be turn
off when the temperature rises to 20.5°C. When the thermostat is on,
the symbol Heater On is indicated.
When the temperature is above 40°C ‘HI’ will be shown on the
LCD and ‘LO’ will be shown when temperature falls below 0°C.
When the voltage of the battery is low, the LCD will turn off. In this
case, the batteries should be changed as soon as possible.
SPECIFICATIONS
Power Source:
two AAA 1.5V Alkaline batteries
Temperature Measurement:
0 - 40°C
Temperature Accuracy:
±1.0°C
Temperature Control:
5 - 35°C
Temperature Control Span:
1°C
Output On Delay:
20 seconds
Working frequency
433,92 MHz
Working distance
up to 100 m (open area)
Coding:
digital, each thermostat has
a unique floating code
Operating Temperature:
-10°C to 50°C (non-condensing)
Storage Temperature:
-30°C to 60°C
Size:
73.5 X 28.0 X 73.5 mm
Material: Polycarbonate
(PC)
Weight:
90 g (battery not included)
Can be operated according to ERC REC 70-03
Hereby, Jablotron Ltd., declares that this TP-98
is in compliance with
the essential requirements and other relevant provisions of Directive
1999/5/EC.
Note:
Dispose of batteries safely depending on the type of the
batteries and local regulation. Although this product does not contain
any harmful materials we suggest you to return the product to the
dealer or directly to the producer after usage.
Internet: www.jablotron.cz
Tel.: +420 483 559 999
fax: +420 483 559 993
Pod Skalkou 33
466 01 Jablonec nad Nisou
Czech Republic
