17
Running over voltage (not yet)
E18
电机过载（暂无）
Motor overload (not yet)
请检查机头是否卡死或者转动困难；
请检查电机插头是否松动或脱落；
上述如仍无法解决请联系当地服务商或拨打
4008876858
。
Please check whether the machine head stuck or not, or rotate very tough
；
Please check whether the motor plug and sensor connection loose or not, or fall off ;
if cannot solve the problem, please contact with the local agent or call 4008876858.
E19
电流检测回路异常
Current detection loop fault
请尝试关闭电源重启如仍无法解决请联系当地服务商或拨打
4008876858
。
Please try on power off and restart, if cannot solve the problem, please contact with the
local agent or call 4008876858.
E20
电源关闭
Power off
E24
语音芯片工作异常
Voice chip working fault
请尝试恢复出厂设置或将电源重启；
上述如仍无法解决请联系当地服务商或拨打
4008876858
。
Please try to do factory reset or restart, if cannot solve the problem, please contact with
the local agent or call 4008876858.
E26
转接板与控制器通讯异常
Adapter plate and controller
communicates fault
请检查转接板与控制箱连接线是否松动；
请尝试恢复出厂设置或将电源重启；
上述如仍无法解决请联系当地服务商或拨打
4008876858
。
Please check if the connection between transfer board and control box loose or not;
Please try factory reset or restart.
If cannot solve the problem, please contact with the local agent or call 4008876858.
E27
恢复出厂设置错误
Factory reset fault
关机重启后，重新恢复出厂设置。
After Power off ,then do the factory reset.
E28
剪线电磁铁报错
Shearing electromagnet control
fault
E29
抬压脚电磁铁报错
Voltage foot electromagnet
control fault
EA1
计件数升序计数满
The ascending count is full
按 P 键清除，或设置 P71 项参数为 5。
Press P to clear, or change value to
“
5
”
in parameter P71.
EA2
计件数降序计数满
The descending count is full
按 P 键清除，或设置 P71 项参数为 5。
Press P to clear, or change value to
“
5
”
in parameter P71.
注意
Note
：
1
、当系统报
E06
（
压脚安全保护
）时，在压脚放到正确位置后，按
P
键（
）清除
E06
错误。
2
、全智能模式下，
E6
、
E7
、
E/8
无法通过更改
P57
、
P58
、
P59
参数值为
0
清除。
3
、当系统报
E05
（停针信号异常）时，系统自动将
P2
更改为
0
，
10s
后自动清除错误。
注：计件数计数满，暂无对应语音，报错时播报“预留”。
1
、
When the screen show E6(presser foot safety protection),when the press foot come back to correct position,
press
（
）
to clear E06.
2
、
In the fully intelligent mode,E6
、
E7
、
E/8 can not be cleared by changing P57
、
P58
、
P59 values to 0.
3
、
When the system reports E05 (abnormal stop signal), the system automatically changes P2 to 0, and
automatically clears the error after 10 seconds.
Note:When the counting is full, there is no reference voice,error reporting
”
reservation
”
.
6
警告码说明表 Warning Code Instructions
序号
No.
内容
Content
对策
Countermeasure
A-01
前传感器自动校准失败
Automatic calibration failure
of front sensor
检测前传感器的接收和发送器表面是否干净
Whether the surface of the receiver and transmitter of the front sensor before
detection is clean or not
A-02
中传感器自动校准失败
Automatic calibration failure
of middle sensor
检测中传感器的接收和发送器表面是否干净
Whether the surface of the receiver and transmitter of the middle sensor
before detection is clean or not
A-03
后传感器自动校准失败
Automatic calibration failure
检测后传感器的接收和发送器表面是否干净
Whether the surface of the receiver and transmitter of the back sensor before
