background image

 

3

IMPORTANT SAFEGUARDS 

Before the ice maker is used, it must be properly positioned and installed as 
described in this manual, so read the manual carefully. Jackson Grills strongly 
recommends that you have a professional install your new machine. The 
warranty may be affected or voided by an incorrect installation .To reduce the 
risk of fire, electrical shock or injury when using the ice maker, follow basic 
precautions, including the following: 

 

 

 

 

Plug into a grounded 3-prong outlet. Do not remove grounding prong, do not use adapter, and 
do not use an extension cord. 

 

It is recommended that a separate circuit, serving only your ice maker, be provided. Use 
receptacles that cannot be turned off by a switch or pull chain. 

 

Do not connect or disconnect the electric plug when your hands are wet. 

 

Never unplug the icemaker by pulling on the power cord. Always grip the plug firmly and 
pull straight out from the outlet. 

 

Never clean ice maker parts with flammable fluids. Do not store or use gasoline or other 
flammable vapors and liquids in the vicinity of this or any other appliance. The fumes can 
create a fire hazard or explosion. 

 

Before proceeding with cleaning and maintenance operations, make sure the power line of the 
unit is disconnected and the water line is shut off. (EXCEPTION: When cleaning the 
machine’s ice making and water systems - See pages 21-22) 

 

Before operating, put all panels back into place. 

 

Never allow children to operate, play with or crawl inside the ice maker. 

 

Do not touch the evaporator by hand when the machine is operating. 

 

Unplug the ice maker or disconnect power before cleaning or servicing. Failure to do so can 
result in electrical shock or death. 

 

Do not attempt to repair or replace any part of your ice maker unless it is specifically 
recommended in this manual. All other servicing should be referred to a qualified technician. 

 
 
 
 
 

Summary of Contents for BBQ10700



























Reviews: