14
At least 36
” clearance maintained from combustible constructions to the sides and back of this grill.
There is no unprotected combustible construction over the grill.
All internal packaging removed.
Burners are sitting properly on orifices.
Knobs turn freely.
The regulator & hose connected to grill is provided by the manufacturer (pre-
set for 11.0” water column).
Unit tested and free of leaks.
User informed of gas supply shut off valve location.
DEAR CONSUMER, PLEASE KEEP THIS MANUAL FOR FUTURE USE
。
BEFORE LIGHTING:
Carefully i
nspect the gas supply hose before turning the gas “ON”. If there is evidence of cuts, wear, or
abrasion, it must be replaced before use, the replacement hose assembly shall be that specified by the
manufacturer.
VERY IMPORTANT: ALWAYS INSPECT THE HOSE BEFORE EACH USE OF THIS GRILL.
TO LIGHT MAIN BURNERS OF THE GRILL:
1.
Read instructions before lighting.
2.
Turn all knobs to
“OFF” then open the L.P. tank valve. Always keep your face and body as far from
the grill as possible when lighting
.
3. Open lid during lighting.
4.
Push and turn any control knob slowly to “HI” position. The built-in igniter will click and spark
simultaneously to light the pilot and burner in sequence. Turn the control knob to OFF
IMMEDIATELY if the burner does not light within 5 seconds, wait 5 minutes for gas to dispel, then
repeat the lighting procedure.
5.
Follow match lighting instructions if burner can
’t be lit after repeated 3-4 times.
Keep a spray bottle of soapy water near the gas supply valve and check the connections
before each use. Do not light the grill if odor of gas is present, call our service center
FLAME CHARACTERISTICS:
Check for proper burner flame characteristics. Each burner is adjusted prior to shipment; however,
variations in the local gas supply may take subtle necessary adjustments.
Burner flames should be blue and stable. There should be no excessive noise, or flame lifting. If any of
these conditions exist please call your Dealer. If the flame is yellow, it indicates insufficient air. If the
flame is noisy and tends to lift away from the burner, it indicates too much air.
NOTE: small yellow tips are ok
TO LIGHT REAR BURNER OF THE GRILL:
THE WARMING RACK MUST BE REMOVED BEFORE LIGHTING THE REAR BURNER!
1. Read instructions before lighting.
2. Turn all knobs to
“OFF” then open the L.P. tank valve. Always keep your face and body as far from
INSTALLER FINAL CHECK LIST
BEFORE LIGHTING:
Finally i
nspect the gas supply hose before turning the gas “ON”. If there is evidence of cuts, wear, or
abrasion, it must be replaced before use, the replacement hose assembly shall be that specified by the
manufacturer.
VERY IMPORTANT: ALWAYS INSPECT THE HOSE BEFORE EACH USE OF THIS GRILL.
TO LIGHT MAIN BURNERS OF THE GRILL:
1.
Read instructions before lighting.
2.
Turn all knobs to
“OFF” then open the L.P. tank valve. Always keep your face and body as far from the
grill as possible when lighting
.
3. Open lid during lighting.
4.
Push and turn any control knob slowly to “HI” position. The built-in igniter will click and spark
simultaneously to light the pilot and burner in sequence. Turn the control knob to OFF IMMEDIATELY
if the burner does not light within 5 seconds, wait 5 minutes for gas to dispel, then repeat the lighting
procedure.
5.
Follow match lighting instructions if burner can
’t be lit after repeated 3-4 times.
TO LIGHT THE MAIN BURNERS BY MATCH (AS THE FIGURE SHOWN ON NEXT PAGE):
If the burner will not light after several attempts then the burner can be match lit.
Tools:
Lighting rod (hanging behind the right door)
Usage:
1. Read instructions before lighting.
2. Open the lid during lighting.
3. Simply place a lighted match between the coils on the end of the lighting rod and hold next to the burner
to ignite.
4. Push and turn the knob to
“HI” position, make sure the burner lights and stays lighted.
5. Repeat 3.4 to light other burners.
GRILL LIGHTING INSTRUCTIONS
LIST
Summary of Contents for JENC-LP
Page 6: ...6 EXPLODED VIEW PARTS LIST...
