6
7
C.4. Speed dial configuration
Phone book:
Set the speed dial phone number
C.5. Upgrade Mode
Upgrade Firmware:
Click ‘Browse’ to select the application
that needs to be updated, click ‘Start
Upgrade’ button to begin the Upgrade
procedure. After successful upgrade,
back to the initial login state.
D.
HOW TO USE THE TELEPHONE
Placing a call
1. Pick up the handset or press
.
Dial Directly
1. Set “Use # to dial immediately” on web page “Voice-Dial
Rules Settings” to “Yes” mode.
2. In On-hook mode, press the desired number and press
#
key to dial out .
Redial
1. In Off-hook mode, press the
REDIAL
key.
Note:
Follow the steps below to set whether Redialled
number disappears or not when the phone is on on-hook
state:
To activate
“Redialled number disappears”:
Press
HOLD
+ *
+
HOLD
+
REDIAL
To cancel
“Redialled number disappears”:
Press
HOLD
+
#
+
HOLD
+
REDIAL
Speed dial
1. Programming the service buttons
Programming the service buttons manully: On-hook, press
HOLD
(HOLD light is on) + the storing guest
service button/message waiting light.
Programming the service buttons by web: Please open the
“Phonebook” on the web page, insert the storing number
one by one, press OK.
2. Placing a call
When the phone is in off-hook status, press a service
button to dial the stored number.
Hold
During a call, press
HOLD
on the base to put the current
party on hold and send hold music to them. Indicator LED
will light up. Press
HOLD
again, the current call will release
call hold.
Mute Function
During a call, press
MUTE
to stop the transmission for
handset and speaker.
Volume Adjustment
In off-hook mode press
or
to adjust the voice
volume of the base.
In on-hook mode press
or
to adjust the ringer
volume of the base.
Note: The phone can be programmed to restore the default
level after hanging up.
Press
HOLD
+
#
+
HOLD
+
returns to default
level.
Press
HOLD
+ *
+
HOLD
+
remains at same level.
Hot Line Function
Please choose the “Use Hotline” option on “SIP PROXY-
Advanced SIP Settings” through WEB, input the Hotline
Number, then click “OK”. SIP phone would automatically
dial the hot line number once SIP phone off-hook, cannot
dial the other number, but can receive the incoming call
normally.
Flash
With SIP phone off-hook, pressing
FLASH
means the phone is
first on-hook then off-hook.
Message Waiting Indicator (MWI)
Message Waiting notifications in SIP are made with the
notify method.
The MWI will flash if there is a message. Pick up the handset
or press the speaker
, then press the MESSAGE button
– The phone will dial out the preset message service
number. The MESSAGE LED will turn off once the message
has been collected.
Restore factory settings
With SIP phone activated by power and on-hook, press
5
+
*
+
5
+
#
, the phone will restore factory
settings.
POE Power
This device’s POE power is level 2 and 6.49W max.
E.
INSTALLATION ATTENTION & MAINTENANCE
The phone has been manufactured using the very latest
technology, and the highest quality components and
workmanship, under ISO9001 quality control procedures.
It can be relied on to provide many years of trouble-free
service, especially if these simple tips are followed:
s
Handle with care, avoiding hard knocks and shocks.
s
Do not expose this product to dust, strong sunlight,
humidity, high temperature, or mechanical shock.
s
Do not use corrosive or abrasive cleansers on this
product. Keep the unit dust free by wiping it with
a soft, dry cloth.
s
Do not tamper with or attempt to modify the phone,
it would make it unsafe to use. Should any service
difficulties or faults be encountered, the following
list may help you identify and remedy problems. In
many cases, however, it may be necessary to call the
distributor from whom you purchased it.
F.
TROUBLESHOOTING
1.
No dialing tone
s
Check the telephone network
s
Check the connection of handset cord and straight
line cord
2.
No ringing or no continuous ring
s
Check the telephone line
s
Check the quantity of parallel phone set
s
Check flash settings
3.
Noise during talk
s
Check the telephone line
s
Check the handset cord
G.
FCC APPROVAL
Complies with Part 68 of the FCC rules. On the bottom of this
telephone is a label that contains, among other information,
the FCC registration number and the ringer equivalence
number (REN) for this telephone. If requested, you must
provide this information to the Telephone Company.
H.
EC DECLARATION OF CONFORMITY
Hereby Bittel declares that this equipment
(Telephone IP60, type JJ IP60) is in compliance with the
essential requirements and other relevant provisions
of Directive 2014/53/EU.
I.
JACKS
Use RJ11C USOC standard modular jacks.
Summary of Contents for IP60
Page 1: ...Telephone IP60 User Manual...
