background image

August 2015© 

Jacobsen HR9016 ROPS Cab Operator Manual

 

 

9. Use your turn signals, checking for traffic well in advance of turning

If the mower is not 

equipped with turn signals and law requires them, install them prior to operating on or near 

public roads. 

 

 

Safety Decals 

 

1. Keep decals clean. Remove dirt with a wet clean cloth when necessary. 

2. Replace safety decals if destroyed, missing, painted over or unreadable. If any safety decals 

are covered or  obscured when the ROPS  is mounted,  it is recommended that you purchase 

replacement decals from the mower manufacturer. Mount them in a readable location at, or 

near, their original location before operating the mower. 

3. New ROPS decals and mower decals are available from your mower dealer. 

 

 

ROPS Safety 

 

1. Install the ROPS in accordance with Tektite mounting instructions. Failure to do so may affect 

the ROPS ability to withstand a roll over.  

2. If the ROPS is subjected to alteration, structural damage or involved in an over turn accident, 

the entire structure must be replaced. Failure to do so may result in injury or death in the event 

of a roll over. 

3. If the mower in not equipped with seat belts, purchase approved seat belts from the mower 

manufacturer or Tektite prior to operating the mower. 

4. Always fasten seat belts prior to operating the mower. 

5. Always operate the mower from the operator’s seat. 

6. Remove mud, crop residue, chains and tools from steps and operator’s platform. They may 

interfere with pedal operation or entry/exit from the mower. 

7. Remove all loose chains, tools, and equipment from the operator’s platform. Failure to do so 

may cause injury or death in the event of a roll over. 

8. Do not install the ROPS on a mower model that the ROPS is not designated for (compatible 

mower  designations  are  printed on the ROPS  serial number plate).  The ROPS is designed 

specifically for individual models to ensure ROPS requirements will be met. Installing the ROPS 

on a non designated mower may result in injury or death. 

 

 

Emergency Exits 

 

This ROPS cab has 2 exits, which may be used in an emergency: left and right side doors. 

 

 

 

Summary of Contents for HR-9016 Turbo





















Reviews: