D-5
FRONTLINE 960 Serie LQ
WARTUNGSHANDBUCH UND ERSATZTEILLISTE
D
3
SICHERHEITSHINWEISE
3.6 VERLASSEN DES FAHRERSITZES
•
Die Maschine auf einem ebenen Boden parken.
•
Vor Verlassen des Fahrersitzes den Motor
abstellen und sicherstellen, daß alle
beweglichen Teile stillstehen. Die Bremsen
anziehen und alle Antriebe deaktivieren. Den
Zündschlüssel abziehen.
3.7 GEFÄLLE
BEI DER ARBEIT AUF GEFÄLLEN IST
BESONDERE VORSICHTIG ANGEBRACHT
•
Lokalisierte Unebenheiten und Senkungen
ändern das allgemeine Gefälle. Bodenzustände,
die ein Rutschen der Maschine verursachen
könnten, sind zu vermeiden.
•
Auf Gefällen und beim Fahren von engen Kurven
ist eine langsame Maschinengeschwindigkeit
erforderlich.
•
Ein plötzliches Beschleunigen oder Bremsen
kann ein Anheben der Hinterräder verursachen.
Daran denken: Ein ‘sicheres’ Gefälle gibt es
nicht.
•
Beim Fahren auf mit Gras bedeckten Gefällen
ist besondere Vorsicht geboten.
NICHT AUF GEFÄLLEN MIT EINER NEIGUNG VON
MEHR ALS 15° VERWENDEN.
WICHTIG: Beim Arbeiten auf einem Abhang die
Raddruckverstärkung auf die maximale (+) Einstellung
setzen, falls angebracht.
3.8 BLOCKIERTE SCHNEIDEVORRICHTUNGEN
•
Den Motor abstellen und sicherstellen, daß alle
beweglichen Teile stillstehen.
•
Die Bremsen anziehen und alle Antriebe
deaktivieren.
•
Die Blockierung vorsichtig entfernen. Alle
Körperteile von der Schneidkante fernhalten. Vor
Energie im Antrieb acht nehmen, die nach
Entfernen der Blockierung ein Rotieren
verursachen könnte.
•
Andere Personen von den Schneidvorrichtungen
fernhalten, da das Drehen eines Zylinders ein
Rotieren der anderen Zylinder verursachen
könnte.
3.9 EINSTELLUNGEN, SCHMIERUNG UND
WARTUNG
•
Den Motor abstellen und sicherstellen, daß alle
beweglichen Teile stillstehen.
•
Die Bremsen anziehen und alle Antriebe
deaktivieren.
•
Alle entsprechenden Anweisungen zur Wartung
lesen.
•
Nur vom ursprünglichen Hersteller gelieferte
Ersatzteile verwenden.
•
Sicherstellen, daß keine anderen Personen
irgendwelche Schneidvorrichtungen berühren, da
ein Drehen eines Zylinders ein Rotieren der
anderen Zylinder verursachen könnte.
•
Zum Reduzieren der Brandgefahr müssen Motor,
Schalldämpfer und Batteriefächer frei von Gras,
Blättern oder übermäßiger Schmiere sein.
•
Verschlissene oder beschädigte Teile aus
Sicherheitsgründen auswechseln.
•
Sicherstellen, daß bei der Arbeit unter
angehobenen Teilen oder Maschinen diese
ausreichend abgestützt sind.
•
Bei der Demontage der Maschine müssen
Kräfte, die eine plötzliche Bewegung von Teilen
verursachen könnten, immer deaktiviert oder
festgehalten werden.
•
Die Maschinendrehzahl darf nicht über die in
den technischen Daten für den Motor
angegebenen Höchstwerte eingestellt werden.
Weder die Einstellungen des Motorregulators
ändern noch die Maschine mit zu hoher
Drehzahl betreiben. Ein Betrieb des Motors mit
zu hoher Drehzahl könnte die Gefahr einer
Personenverletzung erhöhen.
•
Beim Tanken DEN MOTOR ABSTELLEN UND
NICHT RAUCHEN. Kraftstoff vor dem Anlassen
des Motors und niemals, während der Motor
läuft, einfüllen.
•
Beim Einfüllen von Kraftstoff von einem Kanister
in den Tank ist ein Trichter zu verwenden.
•
Den Kraftstofftank nicht über den unteren Teil
des Tankeinfüllstutzens hinaus füllen.
•
Den Einfüllverschluß des Tanks und die Deckel
des Behälters wieder sicher anbringen.
•
Kraftstoff in eigens für diesen Zweck bestimmten
Behältern lagern.
•
Nur im Freien tanken und beim Tanken nicht
rauchen.
•
Wenn Kraftstoff verschüttet wurde, nicht
versuchen, den Motor anzulassen, sondern die
Maschine von diesem Bereich entfernen und
verhindern, daß eine Zündquelle geschaffen wird,
bevor sich die Kraftstoffdämpfe zerstreut haben.
•
Den Motor abkühlen lassen, bevor er in einem
eingeschlossenen Bereich gelagert wird.
•
Während Kraftstoff im Tank ist, die Maschine
niemals in einem Gebäude lagern, in denen die
Dämpfe eine offene Flamme oder Funken
erreichen können.
•
Wenn der Kraftstofftank geleert werden muß,
muß das im Freien geschehen.
Summary of Contents for ransomes frontline 930
