background image

OPERATION    4

17

4.6 TO DRIVE / TRANSPORT ____________________________________________________

Read and follow all safety notes contained in this manual

when driving or transporting tractor. Refer to 

Section 4.3

for general operating instructions. When operating in

reverse look behind you to ensure you have a clear path.

Important: 

If this tractor is driven on public roads, it must

comply with federal, state, and local ordinances. Contact

local authorities for regulations and equipment

requirements. 

The tractor is equipped with a transport lock to lock the

reels in their upright position. Use the transport locks
where required for transporting machine over rough

terrain, on public roads or on trailers. 

To raise mowers to their transport position:

Set reel/3WD switch to OFF. Depress and hold the lift

pedal until the mowers are in their fully raised (transport)

position. 

To engage transport locks:

1. Raise reels to their transport position.
2. Disengage all drives, engage parking brake, and

stop engine.

3. Remove pin (

A

) and slide handle (

B

) from the top

slot (

C

-Storage Position) to the bottom slot (

D

-

Transport Position). Insert pin (

A

) to lock handle (

B

)

in place.

The operator has the option to transport in either 2 wheel
drive (2WD) or 3 wheel drive (3WD). 

Figure 4B

4.7 HILLSIDE OPERATION _____________________________________________________

The mower has been designed for good traction and

stability under normal mowing conditions; however, use

caution when operating on slopes, especially over rough

terrain, or when the grass is wet. Wet grass reduces

traction and steering control.

1. Always mow with the engine at full throttle but reduce

forward speed to maintain the proper cutting

frequency.

2. If the mower tends to slide or the tires begin to

“mark” the turf, angle mower into a less steep grade

until traction is regained or tire marking stops.

3. If mower continues to slide or mark the turf, the

grade is too steep for safe operation. Do not make

another attempt to climb, and back down slowly.

4. When descending a steep slope, always lower

implements to the ground to reduce the risk of

mower overturning.

Correct tire pressure is essential for maximum traction.

Front - 10-12 psi (69-83 kPa).

Rear - 8-10 psi (55-69 kPa).

NOTICE

Engage locks when storing machine overnight. To

prevent damage to the tractor, the transport lock must

be disengaged before reels can be lowered for cutting.

A

B

C

D

A

B

C

 

WARNING

To minimize the possibility of overturning, the safest

method for operating on hills and terraces is to travel

up and down the face of the slope (vertically), not

across the face (horizontally). Avoid unnecessary

turns, travel at reduced speeds, and stay alert for

hidden hazards and drop offs.

 

CAUTION

 Do not operate this mower on slopes greater than

16.2°.

!

!

Summary of Contents for Tri King 67043































Reviews: