background image

4    OPERATION

18

4.8 MOWING_________________________________________________________________

To mow:

1. Disengage transport lock. See 

Section 4.6

.

2. Start the engine and lower the mowers to the

ground. The lift cylinder must be fully extended for

the mowers to float properly.

3. Turn reel/3WD switch to ON and disengage parking

brake.

4. Move throttle lever to FAST then slowly depress

traction pedal to the desired mowing speed.

a. For complete even cutting, overlap swaths by a

few inches.

b. Stop and raise the mowers to the transport

position when crossing paths or roadways. Look

out for traffic.

5. To remove or install the grass catchers, lower the

cutting units to the ground, engage the parking

brake, and shut off the engine. Tilt the grass catcher

body so the front edge clears the mower frame, and

slide the catcher onto or off the catcher frame.

4.9  TOWING / TRAILERING _____________________________________________________

If the tractor experiences problems and must be shut

down and removed from the area, it should be loaded

onto a trailer for transport. If a trailer is not available, the

unit can be towed slowly short distances. 

Use care when loading and unloading tractor. Fasten

tractor to trailer to prevent tractor from rolling or shifting

during transport.

Before towing, open tow valve. The tow valve permits

moving the tractor without starting the engine and

prevents possible damage to hydraulic components.

The tow valve is located on the drive pump beneath the

right hood. To open valve, loosen nuts (

F

) on screw (

G

).

Turn screw inwards to depress tow valve pin (

H

).

Close valve completely and replace cover after towing.

Figure 4C

 

WARNING

To prevent serious injuries, keep hands, feet, and

clothing away from cutting unit when the blades are

moving. 

NEVER

 use your hands to clean cutting units. Use a

brush to remove grass clippings from blades. Blades

can be sharp and could cause injuries. 

To clear obstructions from cutting unit, disengage reel

switch, engage parking brake, stop engine, and

remove key from ignition switch; then remove

obstruction.

!

NOTICE

To prevent damage to the reel and bedknife, never

operate reels when they are not cutting grass.

NOTICE

Do not exceed 2 MPH (3.2 KPH) while towing. Long

distance towing is not recommended.

G

F

H

Summary of Contents for Tri King 67043































Reviews: