background image

6/55

•  Do not mount charger on wall or permanently affix 

charger to any surface.

 The charger is intended to use on 

a flat, stable surface (i.e., table top, bench top).

•  Do not operate charger with damaged cord or plug

 

-

 have them replaced immediately.

•  Do not operate charger if it has received a sharp 

blow, been dropped, or otherwise damaged in any 
way. 

Take it to an authorized service center.

•  Do not disassemble charger;

 take it to an authorized 

service center when service or repair is required. Incor-
rect reassembly may result in a risk of electric shock, 
electrocution or fire.

•  Disconnect the charger from the outlet before at-

tempting any cleaning.

 This will reduce the risk of electric 

shock. Removing the battery pack will not reduce this risk.

•  NEVER attempt to connect 2 chargers together.
•  The charger is designed to operate on standard 

household electrical power. Do not attempt to use 
it on any other voltage.

•  Battery chargers contain electronic parts.

 Dispose 

of properly.

5.1. Charging procedure

JACTO charger supplied with this sprayer is designed to charge JACTO batteries of 
the JB line. The JB1680 model is charged in 5 hours.

1. 

Remove the battery from the sprayer.

2. 

Plug the charger into an appropriate outlet before connecting the battery 

pack. Make sure the AC cord is well attached to the charger.

3. 

Connect the charger plug to the battery pack connector.

4. 

The charge light will remain red/orange while charging.

5. 

When battery pack is fully charged, charge light will change its color to 

green.

6. 

As soon as the battery is fully charged, disconnect the battery from the 

charger.

7. 

Unplug charger cord from outlet.

Recharge discharged batteries as soon as possible or battery life may be 

greatly diminished. For longest battery life, do not discharge batteries fully. 

It is recommended that the batteries be recharged after each use.

5.2. Important charging notes

• 

DO NOT charge the battery pack in an air temperature below 0°C or above 

45°C. This is important and will prevent serious damage to the battery pack.

• 

The charger and battery pack may become warm to the touch while charging. 

This is a normal condition, and does not indicate a problem. To facilitate the 

cooling of the battery pack after use, avoid placing the charger or battery pack 

in a warm environment such as in a shed.

• 

Do not freeze or immerse charger in water or any other liquid.

WARNING:

For safe operation, read this manual and manuals 
originally supplied with tool before using the charger.

 

When opening the tool package for the first time, the battery 
pack will not be fully charged. Before using the battery pack 
and charger, read the safety instructions below. Then follow 
charging procedures outlined.

6. Important Safety Instructions for Battery Packs

READ ALL INSTRUCTIONS

•  Do not incinerate the battery pack even if it is severely damaged or is 

completely worn out.

 

The battery pack can explode in a fire. Toxic fumes and 

materials are created when battery packs are burned.

•  Do not charge or use battery in explosive atmospheres, such as in the 

presence of flammable liquids, gases or dust. 

Inserting or removing the bat-

tery from the charger may ignite the dust or fumes.

•  If battery contents come in to contact with the skin, immediately wash 

area with mild soap and water.

 If battery liquid gets into the eye, rinse water 

over the open eye for 15 minutes or until irritation ceases. If medical attention is 

needed, the battery electrolyte for Li-ion batteries is composed of a mixture of liq-

uid organic carbonates and lithium salts.

•  Contents of opened battery cells may cause respiratory irritation.

 Provide 

fresh air. If symptoms persist, seek medical attention.

•  Disposal of used batteries must be made at appropriate points and ap-

proved for receiving such material.

 If a recycling center is not available in your 

area please contact CUSTOMER SERVICE: Dr. Luiz Miranda Street, 1650 CEP 17580-

000 - Pompeia - SP - Phone: +55 (14) 3405-2113 - email: assistencia.tecnicajsfs@

jacto.com.br - Opening Hours: Monday to Friday from 07h00 am to 11h30 am and 

from 13h00 pm to 17h18 pm.

WARNING!

Burn hazard.

 

Battery liquid may be flammable if exposed 

to spark or flame.
•  Charge the battery packs only in 

JACTO

 chargers. 

•  DO NOT splash or immerse in water or other liquids.

 

This may cause premature cell failure.

•  Do not store or use the tool and battery pack in 

locations where the temperature may reach or 
exceed 113°F (45 ºC).

•  Never attempt to open the battery pack for any reason. 

If battery pack case is cracked or damaged, do not 
connect to charger. Do not crush, drop or damage 
battery pack. Do not use a battery pack or charger that 
has been dropped, run over or damaged in any way 
(i.e., pierced with a nail, hit with a hammer, stepped 
on). Damaged battery packs should be returned to 
service center for recycling.

•  Fire hazard.

 

Do not store or carry battery so that 

metal objects can contact exposed battery ter-
minals.

 For example, do not place battery in aprons, 

pockets, tool boxes, product kit boxes, drawers, etc., with 
loose nails, screws, keys, etc. 

Transporting batteries 

can possibly cause fires if the battery terminals 
inadvertently come in contact with conductive 
materials such as keys, coins, hand tools and the 
like.

 Certain regulations prohibit transporting batteries 

on airplanes (i.e., packed in suitcases and carry-on 
luggage) UNLESS they are properly protected from short 
circuits. So when transporting individual batteries, make 
sure that the battery terminals are protected and well 
insulated from materials that could contact them and 
cause a short circuit. 

NOTE: Batteries should not be 

put in checked baggage.

6.1. Storage recommendations for batteries

• 

Store battery packs in clean, dry place and away from direct sunlight and ex-

cess heat or cold.

• 

Store batteries out of reach of children.

• 

For storage periods of more than one month, store battery with half charge. 

This extends battery life.

Summary of Contents for 230937-4
























































Reviews: