background image

2

DESCRIPTION

Throughout this manual are special
statements surrounded by boxes and
preceded by special symbols.

IMPORTANT!

The operational procedures described
in this manual are intended to help
you get the most from your machine
as well as to protect you and others
from harm. These procedures are
guidelines for safe operation under
most conditions, and are not intended
to replace any safety rules and/or laws
that may be in force in your area.

If you have questions regarding

your HP726 Engine Sprayer or if you
do not understand something in this
manual, your Jacto dealer will gladly
assist you.

You may also contact Jacto, Inc. at

the address printed on the back of this
Manual.

WARNING!

A statement preceded by the word
“WARNING” contains information
that should be acted upon to
prevent serious bodily injury.

  CAUTION!

A statement preceded by the word
“CAUTION” contains information
that should be acted upon to
prevent mechanical damage.

Additional attention statements that
are not preceded by the Attention
Symbol are:

IMPORTANT!

A statement preceded by the word
“IMPORTANT” is one that possesses
special significance.

READ AND FOLLOW THIS
MANUAL. FAILURE TO DO 
SO COULD RESULT IN 
SERIOUS INJURY.

WEAR EYE AND HEARING
PROTECTION  AND A PARTICLE
RESPIRATOR AT ALL TIMES
DURING THE OPERATION 
OF THIS UNIT.

DO NOT OPERATE THIS TOOL
IF YOU ARE TIRED, ILL OR
UNDER THE INFLUENCE OF
ALCOHOL, DRUGS, OR
MEDICATION.

Attention Statements

Summary of Contents for HP726































Reviews: