background image

RESPONSIBILITIES OF OTHERS

Inspecting the unit prior to installation is the responsibility of the installer or building contractor who acts on behalf of the user.  They are responsible

for ensuring the unit is free of defect or damage.  Notices are placed on and in the unit and on the shipping carton advising the installer of this responsibility.
In the event of a problem, the unit must not be installed.  The Company is not responsible for failures or damage that could have been discovered, repaired,
or avoided by proper inspection and testing prior to installation.

Damage occurring in transit is the responsibility of the carrier.  The user or installer MUST open the crate and inspect the unit for damage when it is

delivered.  If damage is discovered, it must be reported immediately to the seller and the carrier in writing, and an inspection requested.  Failure of the carrier
to respond should be reported to the seller and the carrier.  Your freight claims should be filed promptly thereafter.

It is the responsibility of the installer, building contractor, or user to provide access for service.  The Company is not responsible for any costs relating

to obtaining access for repair.  The user shall bear such costs and, if appropriate, must seek recovery from the installer.

Damage occurring to the unit during installation is the responsibility of the installer and/or building contractor and damage occurring thereafter is the

responsibility of the user.

Failure of any optional equipment is the sole responsibility of the equipment manufacturer.  (Options and accessories manufactured by the Company

are warranted for ninety (90) days from the original date of purchase for parts only.)

The Distributor or Dealer is responsible for knowing local code requirements and notifying the installing contractor and/or user of these requirements

at the time of purchase.  The Company is not responsible for costs to modify any product to obtain any code approval, such as city, county, or state building
codes.

WARRANTY SERVICE

For the customer's benefit, the Company maintains a list of independent service personnel to perform required warranty service repairs.  Such firms are
not agents or representatives of the Company and cannot bind the Company by words or conduct.

The Company will provide the warranty service described above when the following conditions have been met: the failure is of the nature or type covered

by the warranty; the user has informed an Authorized Jacuzzi Whirlpool Bath

©

 Service Agent or Warranty Service Department Representative of the nature

of the problem during the warranty period; conclusive evidence (e.g., proof of purchase or installation) is provided to the foregoing by the user proving that
the failure occurred or was discovered within the warranty period; an authorized independent service person or Company representative has been permitted
to inspect the unit during regular business hours within a reasonable time after the problem was reported by the user.

In order to obtain warranty service, consult your local telephone book for the location of the nearest Jacuzzi Whirlpool Bath

©

 Authorized Service Agent.

Describe the problem and the Authorized Service Agent will inspect the unit and provide the required warranty service.

If you are unable to contact a Jacuzzi Whirlpool Bath Authorized Service Agent, call or write:

Jacuzzi Whirlpool Bath

Warranty Service Department

P.O. Box 702168

Dallas, TX 75370-2168

Call: (800) 288-4002

To obtain warranty replacement for factory-installed components for Company supplied options and accessories manufactured and supplied by the

Company, call or write the above.  Provide a description of the problem and proof of purchase.  You will be instructed how to obtain replacements and where
to return, at your expense, the failed component(s), option(s), or accessory(ies).

All replacement parts, equipment, and repairs shall assume the remaining warranty period of the part(s) replaced.
The Company's warranty obligation shall be discharged upon tender of replacement or repair.  The customer's refusal to accept the tender terminates

the Company's warranty obligation.

©

 2005   Jacuzzi Whirlpool Bath

©

    BR28000B     4/05

Ninety-Day

Parts Only

Limited Warranty

On

Accessory(ies)

JACUZZI WHIRLPOOL BATH

©

BR28000B

Ninety-Day

Parts Only

Limited Warranty

On

Accessory(ies)

This card must be filled out and returned to the address printed on the other

side within thirty (30) days from date of purchase in order for this warranty to

be come effective.

Purchaser's Name

________________________________________

Purchaser's A

ddress

______________________________________

City

____________________________

State

______

Z

ip

________

Date of 

Purchase

_________________________________________

Model Name

____________________________________________

Serial Number

___________________________________________

Dealer's Name

___________________________________________

Dealer's Address

_________________________________________

1

.
How did you first hear about this Combination Series Bath product?

(    ) Advertisement      (    ) Article in Magazine/Newspaper

(    ) Visited Dealer/Plumbing Supplier      (    ) Yellow Pages

(    ) Builder/Plumber/Remodeler      (    ) Decorator/Architect

(    ) Visited Retailer/Home Center Store

(    ) Word of Mouth . . . Friend/Relative/Acquaintance

(    ) 

Other (Please 

Describe)

______________________________

2

.
Who first gave you specific information about this product (specifications,

prices, etc.)?

(    ) Dealer/Plumbing Supplier      (    ) Builder      (    ) Remodeler

(    ) Plumbing Contractor      (    ) Retailer/Home Center Store

(    ) Decorator/Architect      (    ) Already Installed

3

.
What was the main reason for purchase?

(    ) Styling      (    ) Warranty Service      (    ) Product Features

(    ) Brand Name      (    ) Price      (    )      (    ) Home Resale

(    

) Other

____________________________________________

4

.
Who finally decided which product you would buy?

(    ) Self      (    ) Spouse      (    ) Self and Spouse Together

(    ) Other Family Member      (    ) Designer/Architect

(    ) Builder/Plumber/Remodeler      (    ) Already Installed

5

.
Who installed?      (    ) Already installed/New Home

(    ) Contractor/Plumber when remodeling

(    ) Self/Spouse when remodeling

(    

) Other

____________________________________________

6

.
What is the current market value of this property?

Please estimate 

$

_______________________________________

7

.
What is the age of the 

head of the household?

_____________

y

e

a

rs

8

.
What other manufacturers did you consider?

(    ) Eljer      (    ) Lasco     (    ) Price Pfister      (    ) Aqua Glass

(    ) Kohler      (    ) American Standard      (    ) Sterling

(    
) Other 

(Specify)

_____________________________________

9

.
How long did you shop before purchasing unit?

   

day

(    ) 2 months - 6 months

   

2-7 

days

(    ) 6 months - 1 year

(    ) 1 week - 2 weeks

   

year- 

years

(    ) 2 weeks - 4 weeks

   

+2 

years

(    ) 1 month - 2 months

1

0

.Approximately how long have you 

lived in this home?

___________

1

1

.Please indicate, approximately, the total annual income of your

household.

(    ) Up to $24,999                  (    ) $50,000 to $74,999

(    ) $25,000 to $29,999          (    ) $75,000 to $99,999

(    ) $30,000 to $39,999          (    ) $100,000 to $149,999

(    ) $40,000 to $49,999          (    ) $150,000 and Above

1

2

.Was your purchase process?

(    ) Very easy     (    ) Easy      (    ) Difficult      (    ) Very Difficult

Warranty Registration Card

Summary of Contents for Allusion 7236













































Reviews: