English
Arga™ Bathtubs
Operation Instructions
www.jacuzzi.com
Page 9
To clean the bathtub, use a mild Meguiar’s nonabrasive liquid detergent solution. You can protect and restore the luster to a dulled
acrylic surface by applying Meguiar’s #10 Mirror Glaze, a product specifically designed for use on acrylic finishes.
Never use abrasive household cleaners of any kind on any Jacuzzi Luxury Bath product.
Minor scratches which do not penetrate the color finish can be removed by lightly sanding with #600-grit wet and dry sandpaper.
Restore the gloss using Meguiar’s Mirror Glaze. Major scratches and gouges which penetrate the acrylic surface will require
refinishing. Call Jacuzzi Luxury Bath to find a service agent in your area.
1. First clean with a mild dish soap and warm water; wipe clean with a soft, slightly damp cloth.
2. For more difficult stains such as grease, oil, paint or ink, apply rubbing alcohol; wipe clean with a soft, dry cloth.
3. Avoid abrasive cleansers and solvents, harsh chemicals or those containing lime removal elements. They may damage the finish
and void the warranty.
4. Avoid abrasive scrubbing cloths or pads.
5. Avoid using razor blades or other sharp objects that might scratch the surface.
6. If unsure as to the suitability of a product’s appropriateness for use with these baths, first test a very small amount of the product
on an inconspicuous area of the bath before using on a visible surface.
7. For very difficult stains, Jacuzzi Luxury Bath recommends the following cleansers and materials: Mr. Clean Magic Eraser, Soft
Scrub, Bon Ami or Gray Scotch Brite Pads (DO NOT use Green Scotch Brite Pads).
Minor scratches which do not penetrate the color finish can be removed by lightly sanding with #600-grit wet and dry sandpaper.
Restore the finish using a Gray Scotch Brite Pad. Major scratches and gouges which penetrate the acrylic surface will require
refinishing. Call Jacuzzi Luxury Bath to find a service agent in your area.
Gloss Bathtub Care & Cleaning
Gloss Bathtub Surface Repair
Operation & Maintenance Instructions
Matte Bathtub Care & Cleaning
Matte Bathtub Surface Repair
Troubleshooting Procedures
PROBLEM
PROBABLE CAUSES
REMEDY
Pump/motor does not
start
• No power to pump/motor
• Pump/motor not plugged in
• Pump/motor faulty
• Reset GFCI
• Insert plug securely into outlet
• Ensure control panel is connected to control box
• Contact Jacuzzi Luxury Bath @ 800-288-4002
Pump/motor operates
but no fully adjustable
jets are functioning
• Suction cover/strainer may be clogged • With the motor turned OFF, remove the suction cover/strainer and remove any
debris. Replace the suction cover before operating
Illumatherapy
™
lights
do not operate
• Connector has come loose
• Contact Jacuzzi Luxury Bath @ 800-288-4002
Water leakage from
pump unions
• Overtightened, O-ring may be
pinched or improperly seated, under
tightened
• Loosen unions, check and reseat O-ring. If O-ring has been pinched out of
shape, replace (refer to number below). When tightening union nuts, hand
tighten only
Pump/motor shuts off
by itself before time
elapses
• Motor thermal protection has
deactivated pump/ motor due to
overheating (supply voltage low)
• GFCI tripped
• Inadequate supply wiring
• Let motor cool; thermal protection will reset. Check for proper ventilation (check
supply voltage)
• Reset GFCI; if it continues to trip, do not use this unit. Disconnect the unit and
have the problem corrected by a licensed electrician before using
• Consult a licensed electrician to correct the wiring unit
Waterfall not working
• Swirlpool
™
function not on
• Waterfall button not activated
• Debris in waterfall outlet
• Valve not functioning properly
• Loose connections (wiring)
• Turn on whirlpool
• Press waterfall button (watch for blue lights to flash)
• Use a thin, rigid and non-abrasive material (i.e. credit card) and gently swipe
back and forth until debris is cleared away from the waterfall opening
• Contact Jacuzzi Luxury Bath @ 800-288-4002
If the unit is within the warranty period, contact Jacuzzi Luxury Bath Service Support at 1-800-288-4002 with your bath’s serial number
before work is started. The serial number is located on the Specification/Serial Number Plate.
