background image

SAFETY AND WARNINGS

2

2

IMPORTANT PRECAUTIONS - Read Prior to Use

1. This model applies to swimming pools with flat floors.
2. This model applies to small pools that are compatible with the cleaner’s cable length. Cleaner may be pulled    
    upside down while working in larger pools.
3. 

DO NOT power on the unit when it is outside of the water.

4. Ensure the power cord is connected to a leakage protective device and appropriate earth socket.
5. 

DO NOT operate the cleaner while people are in pool.

6. 

DO NOT attempt to move floaters along the electric cable. Always leave floaters in their original positions.

7. 

BEFORE POWER ON, ensure the cable is fully released to avoid any winding, which could affect the cleaner’s          

   performance or cause damage.
8. Clean the filter tray after each use. A dirty filter tray will affect the normal operation of the cleaner.
9. Cleaner should be stored in cool, ventilated storage, away from direct sunlight.
10. Power supply unit should be placed in a shaded area. To avoid overheating and potential damage of components,  
     never cover the power supply unit.
11. Only authorized personnel should open the cleaner’s motor assembly and power supply unit. Failure to comply  
     will void warranty.
12. To avoid accidents or damage, the power supply unit should be steadily placed at a minimum distance of 3.5m  
      (appr. 12 ft) from the pools edge.
13. 

DO NOT use the cleaner beyond the working environment/conditions stated in this manual. 

14. 

DO NOT uncover the button film on the power supply unit.

15. Close the filtering system of your pool while cleaner is in use.
16. Ensure the power unit is properly positioned for the cleaner to cover full pool surface.
17. For safe operation, the cleaner works on DC 24V

CONGRATULATIONS

Congratulations on your purchase of the Jacuzzi

® 

Comet Robotic Pool Cleaner, an innovative and highly efficient 

pool cleaner. Through its advanced computer-controlled program, the Comet can clean the pool floor 
automatically without draining pool water, while also filtering and ridding your pool of particles and sediments. 

Summary of Contents for Comet















Reviews: