ENGLISH
23
Jacuzzi Whirlpool Bath K339000X 3/06
Spinning Jets Maintenance
(Models equipped with spinning jets)
If hair or other kind of debris gets caught in the bearings of
these jets, it could cause them to stop spinning. This may
require disassembly and cleaning. To do this, simply grab the
nozzle and pull straight out of the jet housing. The bearing
casing will be attached to the nozzle. These can be separated
by holding the casing and pushing the nozzle out from the rear
of the casing. After cleaning, reassemble in reverse.
Purging the Whirlpool System
NOTE: THE WHIRLPOOL SYSTEM SHOULD BE PURGED
AT LEAST TWICE A MONTH
To remove accumulations of bath residue from the whirl-
pool system, it is recommended that a whirlpool bath be
purged at least twice a month. For best results, however, we
recommend that you purge your whirlpool bath after each use
using, Systems Clean™, our exclusive two-part plumbing
system cleaner made specifically for whirlpool baths.
Systems Clean™ is available through an authorized Jacuzzi
Whirlpool Bath distributor or by calling us direct at 1-800-288-
4002.
Systems Clean™
Instructions for use:
Refer to the instructions on the
Systems Clean™ packet.
CAUTION:
DO NOT USE WHILE BATHING! USE EXTREME
CAUTION WHEN HANDLING THIS PRODUCT!
Immediately after
bathing and exiting the whirlpool bath,
leave the bath water in the tub and add more hot water. The
water level in the tub must be at least 2” (5,08 cm)above the
highest jet.
NOTE: Inducted air from the hydromassage
system will cause the Systems Clean™ contents to foam
increasing odor.
Turn OFF the whirlpool air control or turn it to
the lowest setting and pour in the entire contents of PACKET
#1 ONLY directly into the bath water. For best results, pour the
System Clean into the tub near the intake for the circulation
pump and be sure to avoid contact with your skin. Allow the
whirlpool to run for 30 seconds and then add PACKET #2
ONLY.
It is important to use PACKET #1 before PACKET
#2 to avoid a strong odor
. Allow the bath to run for 5 to 10
minutes then drain the tub completely. Refill the tub with cold
water and run for 2 to 3 minutes. Drain completely and rinse
off any residue.
Remember to reset the air valves to your
bathing comfort level.
DANGER: Harmful if swallowed. Eye irritant. Protect your
eyes, skin and mucus membranes from contact with this
product or its concentrated solution. A strong alkaline
product can cause severe burns to the eyes and skin.
If you have followed the standard purging instructions
above and still have an excess accumulation of bath residue
and desire an alternative cleaning mechanism, we recom-
mend
SUPER SYSTEMS CLEAN
™
PLUS
manufactured by
Stearns Packaging to rectify this condition. This may be
obtained by contacting us at 1-800-288-4002. It is recom-
mended that you follow the instructions provided by the
manufacturer with the product. Repeated use may be neces-
sary.
SUPER SYSTEMS CLEAN
™
PLUS
does not replace
the necessity to regularly purge your whirlpool system with
Systems Clean™ as recommended.
NOZZLE
BEARING CASING
PUSH FROM REAR
TO REMOVE
NOZZLE
MAINTENANCE INSTRUCTIONS
Cleaning the Bath
To clean your bath, simply use a mild, nonabrasive liquid
detergent solution. You can protect and restore the gloss to a
dulled acrylic surface by applying Meguiar's #10 Mirror Glaze,
a product specifically designed for use on acrylic finishes. If
Meguiar's is not available, an acrylic polish of equal quality or
automotive paste wax is acceptable.
Never use abrasive household cleaners on any Jacuzzi
Whirlpool Bath product.
Repairs to the Surface
Minor scratches which do not penetrate the color finish
can be removed by lightly sanding with 600-grit wet/dry sand-
paper. Restore the gloss using Meguiar's Mirror Glaze or au-
tomotive paste wax.
Major scratches and gouges which penetrate the acrylic
surface will require refinishing. Ask your Jacuzzi Whirlpool
Bath dealer for special instructions.
Bath Additives
NOTE: DO NOT USE OIL OR OIL BASED BATH ADDITIVES.
If you want to use any kind of bath additive, use only a small
amount of low-foaming powder or crystal substance; the
whirlpool action intensifies the foaming properties of soaps.
The use of certain bath oils, bubble baths and bath addi-
tives may increase the level of accumulations of bath residue
in the whirlpool system. If excess accumulations persist, you
should discontinue use of these products.
