22
Operating instructions
The spa control system has automatic functions that operate
upon start-up and normal operation.
Upon power up, the display shows the following information:
control panel displays current software release (5.59);
"888" (all LED indicators are on: control of operation of all
display segments and indicator lights).
After the initial start-up sequence ends, the actual water
temperature is displayed. If water temperature is below 38° C
(factory setting) and the spa is set in skimming/heating
mode “F1-F3”, the heater will come on. The heater goes off
when water temperature has reached 38° C.
N.B.:
it is normal for the heater to turn on after the spa is first
filled because tap water is often very cold.
Setting water temperature
The spa’s thermostat provides optimum control of water tem-
perature. The temperature set point (set temperature) can be
adjusted from 18 °C to 40 °C. To increase the set temperature,
press button (+). To lower it, press (
–
).
N.B.:
The first press of either
WARMER ( + )
or COOLER ( - ) but-
ton displays the set temperature.
Pump activation
Button 1 activates the two-speed pump, the first press at low speed,
the second press at high speed. Pressing for a third time turns the
pump off. Button 2 activates pump 2, which only operates at high
speed.
Button for spotlight/LED lighting system
This button makes it possible to turn the spa light on.
The light stays on for an hour. This time can be extended by press-
ing the key again.
LED lighting system (optional)
Offers 7 fixed colours and 3 random sequence modes.
Press the "spotlight" button once to turn the light on in "ran-
dom and fadeout" mode. Then press the key repeatedly to turn
the light off or to select one of the 7 fixed colours, a random se-
quence of fixed colours or a random sequence of flashing colours,
in this order:
random with fadeout
- off -
WHITE
- off -
SKY BLUE
- off -
VI-
OLET
- off -
BLUE
- off -
LIGHT GREEN
- off -
DARK GREEN
-
off -
RED
-
random steady colours
-
random flashing
colours
- off.
Press the "Spotlight" button with no more than 3 seconds
between presses. If you press the key after 3 seconds the se-
quence starts over from the "random with fadeout" mode.
NOTE:
Any time the light is manually turned on, it will auto-
matically turn off after approximately 1 hour.
Selecting desired massage action
Each model incorporates a massage selector that allows you to
customize the massage and performance by diverting water be-
tween various jet systems.
Simply turn massage selector to position
A
(Combo),
B
o
C
, to
divert water pressure to various jet groups.
N.B.:
T
he valve is designed to operate in positions A (Combo), B,
and C for optimum performance.
For optimum filtration benefits, leave the valve in position A when
spa is covered. Select position B or C for maximum jet performance
during spa use.
Adjusting Individual Jet Flow
The water flow to the individual jets in your spa can be in-
creased or decreased by rotating the outside jet face.
Many jets are also equipped with a direction adjustment mod-
ule, so that you can aim the jet in the desired position.
N.B.:
always keep at least 6 jets open so as to ensure efficient wa-
ter filtering.
Air controls
Some jets have a dedicated air adjustment. Turn the knob
clockwise to reduce the amount of air or counter-clockwise to
increase it.
To minimize heat loss, all air controls should be closed when the
spa is not in use. Certain jets may not draw air when jets pump
1 is running in low speed; this is considered normal.
Spa Stereo System (optional)
Spas equipped with the optional Jacuzzi audio system offer
enhanced enjoyment.
1
2
1
2
B
A
C
A
B
C
B
A
C
B
C
A
B
C
