Jacuzzi J - LXL Installation Manual And Use & Maintenance Download

Page: 40 / 80

L2:

Partial lock out

(deactivate the jet buttons to prevent unauthorised use of the
hot tub). In this mode, the skimming/heating mode contin-
ues to operate as programmed. The temperature display
flashes when this function is enabled.

Example: the “F3” skim-

ming/heater cycle was enabled prior to choosing lock mode.
The spa continues to perform the “F3” cycle until lock mode is
cancelled, allowing another cycle to be selected.

L3:

Lock Mode (disables the tempe and - buttons to prevent u-
nauthorized temperature adjustments). Filtration/heating cycle will
continue to operate as programmed in this mode. The jets and lights
buttons will still continue to operate as normal. The temperature
display flashes when this function is enabled.

NOTE:

To exit a Lock Mode you will need to re-enter the filtra-

tion/heating modes and select a cycle from F0-F6.

Selecting the Circulation Pump Filtration Cycle

Press and hold the Jets pump 1 (

) and (

) button at the

same time for 3 seconds to access the circulation pump pro-
gramming.
Once you have entered the circulation pump filtration cycle, con-
tinually press the Warmer (

) or Cooler (

) button to scroll

up through the cycles below.
Then select a cycle and press the Jets pump 1 (

) button to ac-

tivate that cycle. upon pressing the jets pump 1 button the sys-
tem will save your selection, exit the program menu and return
to the main menu.

Note:

If no key is pressed for approximately 10 seconds, the system

exits programming mode. No more than one cycle can be activated
at any one time.

0 hours of circulation per day

4 hours of circulation per day

8 hours of circulation per day (recommended
factory default setting)

12 hours of circulation per day

16 hours of circulation per day

20 hours of circulation per day

24 hours of circulation per day

Note:

- Every time the recirculation pump is activated outside of a pro-
grammed cycle (except cycles C0 and C6), this operating time is
subtracted from the following cycle.
- The recommended factory default setting for the JLX Collection
is 8 hours. T
- Running the circulation pump less than the factory recom-
mended time might result in issues with water quality mainte-
nance.

Programming the Clearray

Programming the CLEARRAY (U) system or the Ozoniser (O3)

Press and hold the Jets pump 1 (

) and Cooler (

) button

at the same time for 3 seconds. Scroll pass the circulation pump
programming menus by pressing the Warmer button.

After the last cycle, “C6”, the LED screen will display “U” or “O3”. If
the LED screen is displaying “U” then pressing the Jets pump 1 will
change the sanitizing system from “U” to “O3” and exit the pro-
gramming menu. If the LED screen is displaying “O3” then press-
ing the Jets pump 1 will change the sanitizing system from “O3”
to “U” and exit the programming menu. You will see one of the t-
wo configurations below:

C0, C1, C2, C3, C4, C5, C6, U, 365 (duration count- timer)

C0, C1, C2, C3, C4, C5, C6, O3, =

Note:

For the O3 option the “=” disables the duration count- timer.

If you do not wish to change the option do not press any buttons and
after 10 seconds the display will return to the main menu.

Note :

If the CLEARRAY System has been selected, when the time al-

lotted has expired (365 days) the display screen will flash between
the water temperature and “blb”. At this time the UV lamp bulb must
be replaced, the quartz tube must be cleaned and the duration
count- timer needs to be reset.

Resetting the duration count- timer (CLEARRAY System only)

Once the duration count- timer for the CLEARRAY System has
reached zero, you will need to reset it, replace the UV lamp bulb
and clean the quartz tube.
To reset the duration count- timer:

Press and hold the Jets pump 1 (

) and Cooler (

) button

at the same time for 3 seconds.
Press the Warmer (

) button until the display shows “0”.

If the timer has reached “0”, pressing the Jets pump 1 (

) but-

ton will reset the counter. If the timer is not at “0” pressing the Jets
pump 1 button will not reset it.

Press

Will take you
back to “C0”

Will select
“O3” option
and exit menu

Press