45
guide you through the process of programming the spa to fit
your personal comfort.
Heat and Filter:
Tap (
)
to access the
heating and filtration programming.
Water Care:
Tap (
)
to access the water
care programming.
Lock:
Tap (
)
to access the locking program-
ming.
Time and Date:
Tap (
)
to access the
time and date programming.
Language:
Tap (
)
access the language
programming.
Units:
Tap either
or
for the tempe-
rature display.
Default setting is
.
Wi-Fi:
Tap (
)
to access the Wi-Fi programming.
Back Button:
Tap to go back to the previous menu.
Invert Button:
Tap to invert the display image.
Slider Bar:
Slide the bar up and down to view the se-
lections available.
I
Programming the Heating Mode
Your Jacuzzi spa is equipped with 3 modes of heating.
An automatic mode called “Auto,” where the spa’s temperatu-
re is maintained at all times. An energy saving heating cycle
called “Econo.” A mode that will only activate the heater du-
ring the daytime called “Day” mode.
Note:
The heater will activate when the temperature drops
~1° from the set temperature.
Indicates that the feature is active.
Indicates that the
feature is not active.
Auto heating:
When programmed to “Auto,” the spa will maintain the water
temperature to the set temperature. Heating will occur when
necessary.
To select this mode, tap (
)
next to the “Auto” icon.
Econo heating:
This is an energy saving heating program that allows the spa
to heat during non-peak hours. When programmed to “Eco-
no,” the spa will only be allowed to heat the water between
5:00 PM to 7:00 AM every day of the week. The hours cannot
be adjusted.
To select this mode, tap (
)
next to the “Econo” icon.
Day heating:
When programmed to “Day,” the spa will only be allowed to
heat the water between 7:00 AM to 5:00 PM every day of the
week. The hours cannot be adjusted.
To select this mode, tap (
)
next to the “Day” icon.
I
Programming the Primary Filter
To access the “Primary Filter” feature, you need to use the Sli-
der Bar to scroll down to the “Heat & Filter” menu. Once you
scroll down, tap (
)
to enter the “Primary Filter” program-
ming.
During a primary filtration, the circulation pump, CLEARRAY
and ozone unit (if applicable) are activated. The factory default
cycle starts at 12:00 AM and last for 8 hours. If you elect to
keep this setting, then you can skip this section.
몇
In extreme bitter cold weather we recommend you
program the circulation pump to run 24 hours.
Refer to the "Winterizing" section.
Any time the circulation pump runs outside of a program cy-
cle, e.g. for heating, that run time will be deducted from the
next primary filter cycle. For example, the primary filter cycle is
set to 8 hours every 24 hours but the circulation pump comes
on for 2 hours to heat the water after the cycle has finished.
The next primary filter cycle will only be for 6 hours not 8
hours.
To change the default cycle:
Tap
to program the start time for the cycle.
Slide your finger up and down to roll the time scroll wheels
to adjust the start time.
>
>
Units
Fº
Cº
WiFi
Fº
Econo
Day
Auto
HEAT & FILTER
Primary Filter
Secondary Filter
HEAT & FILTER
>
>
Econo
Day
Auto
HEAT & FILTER
>
>
>
>
>
Language
Time & Date
Lock
Water Care
Heat & Filter
Water Care
WiFi
Heat & Filter
SETTINGS
>
>
>
96
6:45 PM
ON
UV
Primary Filter
12:00
Start
Set
8 00
8:00
End
pm
Start
