Jacuzzi MyWay, Installation, Use And Maintenance Manual

28

Models with water temperature

maintenance system

„

 The device can only be turned on when a hydromassage cycle 

is operating. The device will be turned off when the hydromas-
sage cycle is interrupted.

The device is provide with a safety thermostat which turns 
it off automatically when the water reaches a threshold of 
40°C.

Light

„

 To switch on the light, press the 

 button for a few seconds 

(on the tub edge).
To switch it off, press down the button until the light goes out.

„

 It is possible to have either a white or coloured light; a light 

which changes colour assuming different sequences is also 
available.

The colour sequences are as follows:
-  Cromodream 

(based on a mixed colour sequence)

;

- Relax 

(based on a blue colour sequence)

;

- Energy 

(based on a red colour sequence)

;

- Sun 

(based on a sky blue colour sequence)

.

NOTE:

each sequence begins gradually then, after a few seconds, 

reaches its characteristic intensity.

The individual colours:
- white;
- turquoise;
- green;
- orange;
- violet.

„

 To move from one colour to the next, or to change the se-

quence, repeatedly press the 

 button.

„

 Where the water level in the tub is below that required for 

hydromassage, the light will function at reduced power.
IT IS also possible to turn on the light when the tub is empty, us-
ing it as a courtesy light (the light will function at reduced power 
in this context too).

Sanitization

We recommend the J-MX 07 

(*)

 liquid, offered by Jacuzzi and avail-

able at the Assistance Centres/Authorised Retailers, is used to clean 
the tub hydraulic circuit (approximately once a month dependent 
on how often the hydromassage is used).  

(*) Product not available in all Countries

It is possible to carry out this cleaning operation using the 

same water used for the hydromassage provided that soap, oils, 
cosmetics,have not been used; otherwise, empty the tub and fill it 
once again.
 

In any case, the water level in the tub (free of concentrates) must 

fully cover the highest hydromassage nozzles.

„

 Pour 75-80 ml of J-MX 07 liquid into the tub.

„

 Keep the 

 key pressed down for a few seconds: the pump 

will activate, the spotlight will flash and the sanitization cycle 
will commence.

„

 Once the function has ended, the pump stops and the spot-

light flashes once again.

„

 Open the drain and empty the tub.

NOTE:

the cycle is, by nature, automatic and is characterised by the 

activation and disabling of the pump and the flashing of the spot-
light at low intensity; in any case, the sanitization cycle lasts 10 min-
utes - approximately 1 minute before the end of the cycle, the pump 
is activated once again in order to rinse the pipes and the spotlight 
briefly flashes to indicate the end of the function.
 

The sanitization process cannot be interrupted unless the pow-

er is disconnected via the main switch.

Troubleshooting...

„

The hydromassage does not activate

- Check that the main switch is on.
- Press down on the button for a few seconds and then release it.
- Insufficient water level (when attempting to activate the func-
tion, the light flashes)

Fill the tub to the level indicated (refer to the Chapter, “Hydromas-
sage”) and press the button once again.

„

The hydromassage stops of its own accord

- If the water falls below the minimum level (e.g. drain open), the 
pump stops (the light flashes).

Fill the tub to the level indicated (refer to the Chapter, “Hydromas-
sage”) and press the button once again. 

„

Not many air bubbles come out of the larger hydromassage 

outlets

- Check that the nozzles are open (refer to the Chapter, “Hydro-
massage”).

„

The “strength” of the hydromassage has got weaker

- Check that the nozzles are open (refer to the Chapter, “Hydro-
massage”).
- Clean the air and hydromassage outlets (refer to the Chapter, 
“Maintenance”).