9
pLEasE rEaD tHE InstructIons carEFuLLY BEForE In-
staLLIng.
check for any defects: once the product has been installed,
the guarantee is no longer valid in the event of damage caused
by knocks or abrasion.
InFo
The
pLaY
shower boxes can be installed with or without wall-mount-
ed glass panes and wood footboard. Also, they come with (mod.
tt
)
or without (mod.
tB
) Turkish bath, seat and top (refer to the assem-
bly drawings).
The shower enclosure must be installed in a corner on finished
and tiled (or water-proof ) walls, but without skirting and/or pro-
jecting parts. Assembling and installing the shower enclosure must
be carried out (in strict compliance with the manufacturer's in-
structions) by two people. Given the considerable weight of the
components to be handled, it is advisable to wear protective gloves.
To assemble the various components in the correct way, the
walls of the installation corner must be straight. Wall compensators
let you recover crookedness by up to 10 mm.
attEntIon: (IEc 60335-1/a2 : 2006) the pressure of the
water system that supplies the unit must not exceed
600 kpa (6 bar).
Before starting...
Before proceeding with installation, check that all the relevant pre-
installation operations have been carried out; see the technical
card for this.
If the water supply system is equipped with an instant water
heater, check that this is powerful enough. For gas models,
we recommend that you use models with variable power in
relation to the volume of water drawn off. Do not use hot
water accumulators without pressure.
In areas of very hard water it is necessary to install a scale-re-
mover in the water system, to prevent and/or reduce the for-
mation of scale.
Installing the shower tray
Remove the shower tray from its packaging.
(
1-1a detail 1
) Connect the drainage column to the prepared
drain pipe, and carefully apply silicone to the connections (
detail 2
).
(
only for models TT;
1 detail 3
) After fastening the small pipe
to the drainage column connector, pass it through the hole shown.
(
1 det.4
) During installation, it is advisable to place high-re-
sistance mortar (or a similar material) between the bottom of the
tray and the floor to create a good support base and to keep the tray
from bending under a person's weight. Then set the shower tray on
the floor (
det.5
).
(
2 detail 1
) Fasten the ring nut to the drainage column and
test for water tightness.
Important: it is advisable to check that there are no
leaks from the drain, as it will no longer be possible to
check when it has been assembled. For example, place
the shower tray on spacers (in order to check) and pour
one or more buckets of water into the shower tray.
(
2 detail 2
) Check that the shower tray is flat, if necessary
adjust it at the edge (
detail 3
).
(
2 detail 4
) Fasten the shower tray to the floor using suit-
able a substance.
(
2 detail 5
) Apply silicone between the shower tray and the
walls, as shown.
If the gap that is created between the shower tray
and the walls is considerable, the Service Centres can supply suitable
profiles to cover the silicone.
Installing the compensator-fixture panel
Before proceeding with the following assembly phases, it is advisable
to protect the shower tray from any knocks and/or abrasion.
(
3 detail 1
) Making sure that the compensator is perfectly cen-
tred on the base of the shower tray, mark the position on the wall.
(
3 detail 2
) After checking that the compensator is straight,
mark the points for fastening (
detail 3
).
(
4 detail 1
) Remove the compensator and drill the holes,
then insert the dowels (
detail 2
).
(
4 detail 3
) Apply silicone to the two grooves on the back
of the compensator, along the entire length.
(
only for models TT;
5 detail 1
) Replace the compensator on
the shower tray, making the electric cables come out of the slot
(for the power supply and any others for the alarm circuit and
equipotential connection).
Make sure that all the cables come out of the slot, so that they will
not be squashed by the compensator.
10mm
10mm
90
°
90
°
Summary of Contents for play sphere 90
Page 2: ......
