background image

2

.1B No Heat Or Not Enough Heat

• 

Symptoms: 

Circulation pump (heating pump) not turning, panel heat indicator not lit, 

panel 

is flashing FL2.

Standard Troubleshooting Approach

Pull wire off flow 
switch. Does the FL2 
error message go 
away?

Turn off power to hot 
tub. Test flow switch 
with ohmmeter for 
continuity across 
switch terminals (fig. 
D-E). Does meter read 
continuity (0

Ω

)?

Remove flow switch 
and inspect for debris 
interference. Remove 
debris if present. Test 
switch for continuity 
(0

Ω

) when closed and 

for infinite 

Ω

 when 

open (fig. E). Does 
switch operate cor-
rectly?

Install switch making 
sure flow arrow points 
in direction of flow 
and switch doesn’t 
bottom out in fitting 
(fig. F). Retest system.

Is wire shorted?

Replace wire.

Make sure wire is not 
shorted when in-
stalled on switch.

Replace flow switch.

Replace circuit board.

Yes

No

No

Yes

Yes

Yes

No

No

Fig. D

Infinite

Continuity 0

Fig. E

Infinite

Continuity 0

FLOW

Orientation

Orientation

FLOW

Fig. F

Pipe End

View 

OK

Arrows not

aligned

Arrows 

aligned

Open

Closed

Pump

off 

Pump

on

Summary of Contents for Premium J-315
































































Reviews: