Installation and Operation
www.jacuzzi.com
Page 2
Step 1
sponge.
Turn water supply OFF.
Flush the toilet. Remove remaining water using a
Remove mounting hardware and old toilet.
A su vez cierre el agua.
Descargue el inodoro. Retire el agua restante con una esponja.
Quitar hardware de montaje y servicio de edad.
Presione el anillo de cera firmemente en su lugar,
como se muestra.
Step 5
Wax Ring
Toilet
(Cuenco)
Floor Flange Bolt
(Floor Flange Bolt)
shown to the right).
Instale dos (2)
T- pernos en la brida del piso - como
se muestra a la derecha.)
Step 3
Floor Flange Channel
(Piso brida Canal)
(Limpie el piso existente brida y eliminar viejos
T-pernos.)
Step 2
(La abertura en el piso debe estar cubierto si se deja sin atención por más de 1-2 horas para
evitar que los gases residuales de escape.)
This is a unique installation. Prior to the installation of this product, the installation
instructions must be read and completely understood.
Make sure that none of the parts are missing and/or damaged before beginning instal-
lation. If there are parts missing and/or damaged, please stop the installation and
contact Jacuzzi Luxury Bath Customer Service at 1 800 288 4002 or visit us online at
www.jacuzzi.com.
Esta es una instalación única. Antes de la instalación de este producto, las instrucciones de
instalación debe ser leído y entendido por completo. Asegúrese de que ninguna de estas piezas
se han perdido y / o dañadas antes de comenzar la instalación. Si hay partes que faltan y / o
dañado, por favor, detener la instalación y el contacto Jacuzzi Baño de Lujo cliente Serviceat
1 800 288 4002 o visítenos en línea en www.jacuzzi.com).
Thread two (2)
flat washer onto the floor flange bolt.
(Hilo de dos (2)
separadores de plástico recipiente en el T-pernos.)
The
floor flange bolts
must be parallel to the
wall before proceeding (see below).
(El T-pernos
debe ser paralela a la pared
antes de proceder - ver más abajo.)
Step 4
Flat Washer
Wall
(Muro)
Step 7
Floor Flange Bolt
Floor Flange Bolt
Flat Washer
Flat Washer
Lock Nut
Lock Nut
Bolt Cap
Bolt Cap
10mm Wrench
(10mm Llave)
It is recommended that two people perform
the following step.
(Se recomienda que dos personas
realice el siguiente paso.)
When lowering the unit into place, insure that the
mounting holes on the unit are aligned with the
floor flange bolt
on the floor flange. Press down firmly on
the unit once the unit is in place.
(Al bajar de la unidad en su lugar, asegúrese de que
los agujeros de montaje de la unidad están alineados
con el
T-pernos
de la brida del piso. Presione con
firmeza en la unidad una vez que las unidad esté
en su luga.)
Step 6
Toilet
(Cuenco)
Floor Flange
(piso de la brida)
(Sellar el espacio entre el suelo y el inodoro
con masilla de silicona.)
Do not caulk the rear of the toilet base. Leaks
will not be visible if caulked.
No calafatear la parte posterior de la base del inodoro.
Las fugas no será visible si calafateado.
Level the toilet.
Nivel de la taza del baño.
If the toilet will not level, use shims
to level the toilet.
Si el inodoro no nivel, coloque cuñas
para nivelar el inodoro.
Dual Flush
Step 8
Step 9
Step 10
Step 11
NOTE
NOTES
CAUTION
CAUTION
Jacuzzi
®
Luxury Bath
14525 Monte Vista Avenue
Chino, California, 91710
1-800-288-4002
www.jacuzzi.com
Place the plastic disc nut, flat washers and
lock nut onto the floor flange bolt. Use a
10mm wrench to tighten the lock nut.
Place the bolt cap onto the bowl nut and
press firmly into place.
(Coloque lavadora biselados y
la arandela plana y tuerca recipienteen
el T-bolt.Use una llave de 10 mm para
apretarla tuerca de tazón. Coloque la tapa
de plástico en la tuerca recipiente y presione
firmemente en su lugar.)
Plastic Disc Nut
(Lavadora Biselado)
Clean the existing floor flange and remove old
floor flange bolt.
The floor opening must be covered if left unattended for more than 1-2 hours to prevent
sewage gases from escaping.
Install two (2)
floor flange bolts
into the floor flange (as
Press the wax ring firmly into place, as shown
Seal the space between the floor and
the toilet using silicone caulking.
Position flush button on top of the tank lid so the small button with the blue rod (half flush)
will align with the green button on top of the flush valve preassemble to tank and the larger
button with the white rod will align with the white button in tank lid by hand tightening lock nut.
The flush button may have been assembled at the factory.
Position flush button on top of the tank lid so the small button with the blue rod (half flush)
will aling with the green button on top of the flush valve preassemble to tank and the larger
button with the white rod will align with the white button
in tank lid by hand tightening lock nut. The flush button may
have been assembled at the factory.
(Floor flange bolts must
be parallel with the wall.)
(T-Bolts
debe ser paralelo
a la pared.)
Shims not provided
(Las cuñas no siempre)
Do not overtighten these nuts, or damage may occur.
(No apriete demasiado los frutos secos, O puede producir daño.)
CAUTION
Optional Step
(Paso opcional)
Flush valve
Flush valve
Lock nut
Lock nut
Rod locknut
Rod locknut
Dual flush
Dual flush
Slot Seat Washer
Plastic Seat Bolt
Flat Seat Washer
Flat Seat Washer
Seat Lock Nut
Seat Lock Nut
Plastic Seat Bolt
Plastic Seat Cap
Plastic Seat Cap
Seat Plastic Washer
Línea de suministro de agua conectar, abra el
agua y tire de la cadena. Revise si hay fugas.
Si se observan fugas, revisar todos los terminales
y apriete según sea necesario.
Step 12
Connect the water supply line, turn water
The small button is for a light
flush that takes away only liquids.
It uses only 1.1 gallons of water.
The larger button is for a complete
flushing action that takes away
solids and liquids. This flush uses
1.6 gallons of water and is a standard
flushing action that disposes of waste
and cleans the basin.
The small button is for a light
flush that takes away only liquids. It uses only 1.1 gallons of water.
The larger button is for a complete flushing action that takes away solids and liquids.
This flush uses 1.6 gallons of water and is a standard flushing action that disposes of waste
and cleans the basin.
Small Button
For Liquid
1.1 Gallon Flush
Small Button
For Liquid
1.1 Gallon Flush
Larger Button
For Solid
1.6 Gallon Flush
Larger Button
For Solid
1.6 Gallon Flush
ON and flush the toilet. Check for leaks. If
leaks are noted, check all fittings and tighten
as needed.
Place the plastic cap onto the bowl
nut and press firmly into place.
Coloque la tapa de plástico en la tuerca
recipiente y presione firmemente en su lugar.
Water Supply Line
(Línea de Suministro de Agua)
Lid
(Tapa)
Plastic Cap
(La tapa de plástico)
Place seat on bowl, centering the hinges over the holes
in the bowl. Insert plastic seat bolts into hinge holes and
adjust the toilet seat and lid to find the best assembly
position. Finally, place the flat seat washers onto plastic
seat bolts from underneath the bowl. Use a screwdriver
to secure seat lock nuts. Finish with placing the plastic
seat cap on top. So it covers the plastic seat bolt.
Place seat on bowl, centering the hinges over the holes
in the bowl. insert plastic seat bolts into hinge holes and
adjust the toilet seat and lid to find the best assembly
position. Finally, place the flat seat washers onto plastic
seat bolts from underneath the bowl. Use a screwdriver
to secure seat lock nuts. Finish with placing the plastic
seat cap on top. So it covers the plastic seat bolt.
Push rod
Push rod
