www.jacuzzi.com
Page 5
Experience
English
Pure Air® Auto-Dri™ Air Channels
To remove accumulations of bathtub residue from the whirlpool system, it is recommended that a Whirlpool bathtub be
cleaned at least twice a month. For best results, however, we recommend that you clean your Whirlpool bathtub after
each use using Systems Clean™, our exclusive two-part plumbing system cleaner made specifically for Whirlpool bath
-
tubs. Systems Clean™ is available through an authorized Jacuzzi Luxury Bath distributor, by calling 1-800-288-4002 or
may be purchased online at www.jacuzzi.com.
J2 Auto-Dri™ Air Channels
The blower will operate for 20 minutes and then automatically shut off, unless power is manually turned off. In either
case, 20 minutes after the blower has shut off, it will turn ON for a one-minute drying cycle to blow out any water remain
-
ing in the air system.
If the bath is used without the blower operating (showering or bathing without using the Pure Air® system), initiate the
one-minute drying cycle manually by use of the ON/OFF switch. Turn the switch ON and OFF again as you exit the bath
and the drying cycle will occur in 20 minutes.
J2 Daily Auto-Dri™ Cycle
To Activate: Holding the
button for five-seconds when the blower is off activates the daily Auto-Dri™ cycle. The blower
will start every day at the same time for one-minute. Once the daily Auto-Dri™ cycle is activated, the blower will come on
for one-second, turn off for two-seconds, come on for one-second and then turn off.
To Deactivate: Holding the
button for five-seconds when the blower is off deactivates the daily Auto-Dri™ cycle. When
the daily Auto-Dri™ cycle is deactivated, the blower will come on for one-second and then turn off.
J4 Auto-Dri™ Air Channels
The Auto-Dri™cycle is automatic and will reduce excessive accumulation of residual water in the air channels.
There are two Auto-Dri™ cycles: drain assisted Auto-Dri™ cycle and daily Auto-Dri™ cycle.
J4 Drain Assist
The Auto-Dri™ cycle is sensor assisted – two sensors (metal dials) are located near the drain of the bathtub. The sensors
detect the presence and absence of water in the bathtub.
To ensure effective and correct operation of the water sensors, it is important to keep them clean and free from block
-
age or objects.
After bathing and following the emptying of the bathing well, the sensors detect a “no water” condition. A five minute wait
time elapses and then the blower is activated. The blower will cycle through a range of speeds for 2 ½ minutes, during
which either 2 or 3 indicator lights will flash at various speeds.
•
The Auto-Dri™ cycle will engage even if the blower is not used during bathing.
•
The cycle may initiate more than once if the sensors become wet during any part of the Auto-Dri™ operation or during
routine cleaning of the bathtub. This is normal and does not require attention.
J4 Daily Auto-Dri™ Cycle
Each day, the blower will automatically activate a daily Auto-Dri™ cycle. The blower will operate for one minute on high
power, followed by 15 seconds at ½ power.
To set Auto-Dri™ cycle time:
Wait until the time, which you desire the daily Auto-Dri™ cycle to activate, with the blower off,
press and hold the plus button for five seconds. To confirm that you have set the time, the blower will cycle between on
and off 2 times in a 4 second span.
To cancel daily Auto-Dri™ cycle:
With the blower off, press and hold the plus button for five seconds. To confirm that you
have cancelled the Auto-Dri™ cycle , the blower will come on for 1 second and then stop.
You must set the daily Auto-Dri™ cycle upon installation; the default is no pre-set daily Auto-Dri™ cycle.
If a power failure occurs, the system will default to no daily Auto-Dri™ cycle.
