background image

Normal Operation

Whirlpool System

You can enjoy the Quantum Plus spa with or without

activating the whirlpool.  Either way, bathing in your spa can
be pleasurable, as well as therapeutic.  After a busy,
stressful day, you can look forward to soaking in your spa in
still water with no turbulence—only the gentle warmth of the
soothing and relaxing water.

For a more invigorating spa experience, you can take

advantage of the built-in whirlpool system.  To do this, push
the SYSTEM switch button to select the JETS mode.  Sit or
recline in the spa so you are comfortable.  The six fully
adjustable whirlpool jets can be adjusted to control the force
of the water coming into the spa.  For stimulating action,
increase the force of the flow by rotating the jet handles to
the left.  For a more relaxing effect, rotate the handles to the
right (clockwise).  The directionally adjustable whirlpool jet
located on the wall of the spa opposite the lounger side of
the spa, can be directed toward any location on the body,
particularly toward any area that feels tense or stiff.  The jets
are located at various heights around the seating area to
allow a hydromassage of the upper or lower back.  The
warmth of the water and the stimulating water flow from the
jet will pleasantly increase circulation.

Or, for the total whirlpool effect, you can adjust all jets so

they point in a clockwise or counterclockwise direction to
circulate the air and water mixture in a circular motion all
about the spa.

11

OPERATION

beautiful cascades of shimmering water for an exciting
visual effect.

Activate the waterfall feature by first turning on the JETS,

HTR/FILTER, or FILTER function, then rotate downward
the flow control lever located on the left side of the spout.
Use this lever to adjust the amount of water flowing through
the Water Rainbow spout.  The waterfall effect will be
greatest in the JETS mode.  Turning off the flow at the fully
adjustable jets will dramatically increase the Water Rain-
bow flow.

CAUTION:  The water circulating through the Water
Rainbow spouts is not fresh water and therefore is not
suitable for drinking.

Air Blower

The Quantum Plus features a built-in air blower and

factory drilled air holes in the seats of the spa.

The blower sends air to a channel located under the

spa’s seats; this air is distributed through the air holes, and
as the pressurized air is released from the holes, tiny
bubbles are formed.  These bubbles travel upward through
the water and expand until they reach the surface and burst.
The exciting visual effect of the bursting bubbles contrib-
utes to the overall hydromassage experience.

Activate the blower by pushing the ACC switch.

Filtration

When you are ready to leave the spa, push the SYSTEM

switch button to turn off the whirlpool.  Then select the HTR/
FILTER mode.  Adjust the TEMP CONTROL knob to the
temperature at which you want the water maintained.  In
this way, the water will be filtered when the heater goes on
to maintain the temperature. Running the filter pump for at
least two hours per day is sufficient.  Another way to be sure
the water will be filtered is to turn the SYSTEM off and set
the  timer in the System Control Module to turn the system
on at a preset time everyday.  Maintain the waterlevel to  the
indicator mark on the skimmer/filter frame.  (See page 8 for
instructions on setting timer.)

Silent Air Induction

The intensity of the whirlpool action is determined by how

much air is inducted into the water.  You have control of this
by adjusting the two air induction control knobs locatedon
both control panels.  For maximum air induction, rotate each
control knob fully counter clockwise to the largest dot.  For
fewer air bubbles, decrease the amount of air induction by
rotating the control knob clockwise.  When the knobs are
turned to the smallest dot, only water is being circulated.

Water Rainbow

The Water Rainbow spouts will add the soothing sound

of a waterfall to your bathing pleasure, as well as providing

FULLY ADJUSTABLE WHIRLPOOL JET

WATER RAINBOW SPOUT

Summary of Contents for Quantum Plus 770000

























Reviews: