background image

2 & 3 WALL OPERATION

23

STOP RELEASE

Temperature Valve
The temperature of the mixed water is adjusted by means of the
graduated handle.  This handle has a safety stop set at 100

°

F

(38

°

C).  To increase the temperature, press the red button to release

the stop and keep turning the handle.

Shower Head
There are four selectable positions: Jet, normal pulsating and
aerated flow.

Body Sprays (2 Upper & 2 Lower)
To adjust the flow and intensity, turn as shown.  The spray can also
be turned to change the direction of the spray.

Diverter Control
To turn On water, turn the inner knob clockwise and adjust for more
or less flow.
The outer knob will divert the water to body sprays, shower head
(shown in this position) and foot temperature tester.  If the knob is
pointing anywhere between main functions, the amount of water
will be proportional to where the knob is pointing.  If the knob is
pointing to the white line between positions, the water will be
diverted equally to both functions on either side of the white line.

Foot Temperature Testor

LESS FLOW AND INTENSITY

MORE FLOW AND INTENSITY

BODY

SPRAY

SHOWER

HEAD

FOOT
TEMPERATURE
TESTER

INNER
KNOB

OUTER

KNOB

Summary of Contents for SUMMER RAIN

































Reviews: