background image

WATER RAINBOW
SPOUT

SUCTION
COVERS

SKIMMER/
FILTERS

WATER LEVEL
MARK

SILENT
AIR
CONTROL

DIRECTIONALLY
ADJUSTABLE JET

FULLY
ADJUSTABLE
WHIRLPOOL
JET

SILENT AIR
CONTROLS

18

Spa  Control

Your Spa and equipment pack installation must include a control system such as an air switch and/or timer system

which will turn the two motor/pumps on and off and provide control of whirlpool, heater and filter functions.  Follow
switch manufacturer's instructions for operation.

Warning! At no time should the whirlpool or filter pump motors be activated until the pumps are primed and the spa is
filled with water to its normal operating level.   Running the pump dry will cause irreparable damage to the pump,
and the warranty will become void.

All spa heaters have adjustable thermostat settings.  The recommended water temperature range for  whirlpool bathing

is 90°-98° F. (104° F. max.) .  Following the heater manufacturer's instructions, set your heater thermostat to a point which
is comfortable for you  within that range.  (See Safety Information on the inside front cover.)

Normal Operation

Whirlpool System:

You can enjoy the Cirrus IG spa with or without activating

the whirlpool.  Either way, bathing in your spa can be
pleasurable, as well as therapeutic.  After a busy, stressful
day, you can look forward to soaking in your spa in still
water with no turbulence—only the gentle warmth of the
soothing and relaxing water.

For a more invigorating spa experience, you can take

advantage of the built-in whirlpool system.  To do this,
select  the  WHIRLPOOL  mode    at  the  system  control
switch.  Sit or recline in the spa so you are comfortable.
Since all the jets are directionally adjustable, you can direct
a jet toward an area where muscles feel tense or stiff.  The
warmth of the water and the stimulating water flow from the
jet will pleasantly increase circulation.

 For the total whirlpool effect and all-over feeling of well

being, you can adjust all jets so they point in a clockwise or
counterclockwise direction to circulate the air and water
mixture in a circular motion all about the spa.

OPERATION

FULLY ADJUSTABLE

WHIRLPOOL  JETS

DIRECTIONALLY ADJUSTABLE
WHIRLPOOL  JETS

Summary of Contents for The Cirrus IG






























Reviews: