1
SPOUT ASSEMBLY
2
TEE AND HOSE ASSEMBLY
Insert SPOUT SHANK (1) through center
hole of sink or mounting surface. Make
sure RUBBER WASHER (2) is seated into
groove in SPOUT ESCUTCHEON BASE (3).
Assemble RUBBER WASHER (4),
FIBER WASHER (5) and LOCKNUT (6)
onto threads of SPOUT SHANK (1)
from underside of lavatory or mounting
surface.
Push the TEE (1) onto SPOUT SHANK (2) until it makes full contact
with the 0-RING (3)
Align SPOUT (7) and tighten
LOCKNUT (6). Insert LIFT ROD (8)
through SPOUT (7).
Insert POP-UP ROD (9) into bottom of
faucet and thread into POP-UP KNOB (10).
1
2
4
5
6
Turn off hot and cold water
supplies before beginning.
CAUTION
7
1
2
3
4
5
3
WATER SUPPLY CONNECTIONS
Connect water supply to VALVE BODIES (1) with 1/2" IPS
FLEXIBLE SUPPLIES (3) or 3/8" O.D. BULL-NOSE RISERS (4).
Use wrench to tighten connections.
Do not over tighten. Be careful not to kink copper supply when
bending. Use tubing cutter to cut to proper length.
1
4
FERRULE
NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS MUST BE
PURCHASED SEPARATELY.
COUPLING
NUT
1 0 9 6 4 6
1 0 9 6 4 6
ROUGHING-IN
DIMENSIONS
Plumbers' Putty or Caulking
Adjustable Wrench
Phillips Screwdriver
Channel Locks
TOOLS REQUIRED
Tubing Cutter
Regular Screwdriver
Basin Wrench
GROOVE
O-RING
O-RING
APPLY SEALANT
OR TEFLON TAPE
4
A FOAM SEAL (1) is installed on underside of FLANGE (2). (Plumbers
Putty may be used in place of FOAM SEAL (1) if desired.)
Apply sealant or Teflon tape to threads of TAILPIECE (10) and
thread into DRAIN BODY (7) making a water tight seal.
Drop FLANGE (2) into LAVATORY DRAIN (3). From below assemble
RUBBER GASKET (4), PLASTIC WASHER (5) and LOCK NUT (6) onto
DRAIN FLANGE (2). Do not tighten fully.
INSTALL POP-UP DRAIN
FIG. 4a
FIG. 4b
FIG. 4c
FIG. 4c
FIG. 4a
FIG. 4b
1
4
3
2
5
6
7
8
6
9
2
Adjust STOPPER (13) height by repositioning POP-UP ROD (16) in SWIVEL (15)
and tightening SET SCREW (18).
Assemble POP-UP SWIVEL (15) to PIVOT ROD (11) but do not tighten.
Drop POP-UP ROD (16) through other hole in POP-UP SWIVEL (15) and
tighten SET SCREW (17)
Assemble PIVOT ROD (11), and PIVOT NUT (12) as shown. Install CONCAVE
WASHER (19) into PIVOT ROD OPENING (9) if not preinstalled. Hand tighten
PIVOT NUT (12). Drop STOPPER (13) into drain.
(
To vandal proof drain rotate STOPPER (13) so PIVOT ROD (11) goes
through EYE (14) of STOPPER (13)
. Make connection to "P" TRAP.
Inspect inside DRAIN BODY (7) that SEAL (8) is installed. Thread
DRAIN BODY (7) tight against FLANGE (2) to make a water tight seal.
10
9
7
6
12
19
16
15
17
18
2
10
14
13
11
The PIVOT ROD OPENING (9) in DRAIN BODY (7) should face the rear
of the lavatory. Tighten LOCK NUT (6) on FLANGE (2) to make a water
tight connection with channel locks. Do not over tighten.
3
INSTALL VALVE BODIES
INSTALL HANDLES
HOSE CONNECTIONS
1-3/4'' MAX.
STOP RING
GROOVE
Insert VALVE BODY (2) through mounting hole from underside
of tub deck or mounting surface.
Note: VALVE BODY marked Hot is installed in the left Mtg. hole,
VALVE BODY marked Cold in the right when facing front of fitting.
Maximum mounting surface thickness is 1-3/4".
Install STOP RING (6) onto VALVE BODY (2) if not in place. Install
O-RING (7) into groove in FLANGE (8).
Thread FLANGE (8) flush against STOP RING (6). Thread
ROSETTE (9) onto VALVE BODY (2) until tight against it's
internal stop.
Align VALVE BODY (2) and from below tighten LOCKNUT (1)
to secure VALVE BODY (2).
Turn VALVES to off position. Align HANDLES (10) as shown or
as desired and install onto HANDLE ADAPTER (11). Tighten SET
SCREW (12) with HEX WRENCH (13) supplied. Push PLUG
BUTTON (14) into place.
Insert FIBER WASHERS (15) into COUPLING NUTS (16) of
SUPPLY HOSES (17) and tighten making water tight connection.
Important: Loop SUPPLY HOSES (17) as illustrated so they do not kink.
1
2
16
HOT
COLD
15
17
12
5
16
3
4
7
8
12
14
13
6
11
9
10
JADO
HOT
5-3/4"
3/4"
7-5/8"
6" to 12"
2-1/8"
1-1/4"
2"
max. 2"
4-1/2"
1-3/8" MAX.
1-1/2"
max. 7"
1/2" NPT
1-5/32"
5/8"
1-1/8"
NOTE: MOUNTING HOLES
ARE 1-1/4" D.
Thread LOCKNUT (1) to bottom of VALVE BODY (2). Make sure
SPACER (3), BRASS WASHER (4) and RUBBER WASHER (5) are
installed.
Unpack valve assembly and remove HANDLE (10) by unthreading
SET SCREW (12). Unthread ROSETTE (9) and FLANGE (8)
removing them from VALVE BODY (2).
3
8
10
9
Rotate TEE (2) about 10 degrees from center. Insert HEX
COUPLING NUT (4) into TEE (2) and tighten on end of spout
shank to make a water tight connection. Do not over tighten.
10˚
