ROUGHING-IN
DIMENSIONS
SMALL
END
LARGE
END
LARGE
END
VALVE
OUTLET
VALVE
OUTLET
PUTTY
1
2
3
3
2
4
1
1 0 9 1 5 0
1 0 9 1 5 0
3
BIDET
LEDGE
2-1/2" - 6"
2-1/2" - 6"
1-1/4"
MAX 4"
1-1/16" D.
MAX 7"
MAX 2"
11"
2-1/8" D.
SPRAY
1-1/8 D.
MAX 13"
DIVERTER
AND VACUUM
BREAKER
LIFT ROD
CONNECTIONS ARE FOR1/2" IPS
FLEXIBLE SUPPLIES or 3/8" O.D.
BULL-NOSE RISERS
Plumbers' Putty or Caulking
Adjustable Wrench
Phillips Screwdriver
Channel Locks
TOOLS REQUIRED
Tubing Cutter
Regular Screwdriver
Basin Wrench
3
5
6
INSTALL SUPPLY HOSES
INSTALL SPRAY BODY
INSTALL HANDLES
Connect small end of SUPPLY HOSES (1) TO "Y" ADAPTER (2)
and larger end to each VALVE OUTLET.
Important: Loop SUPPLY HOSES (1) as illustrated
so they do not kink.
Connect one end of SPRAY HOSE (7) to HOSE ADAPTER (8)
and the other end to shank of SPRAY BODY (3). Tighten hose
connections to make a water tight seal.
2
4
1
3
5
6
9
7
8
Hex wench, supplied
BIDET
MOUNTING
SURFACE
For Diverter handle:
Install DIVERTER
HANDLE (5) onto VALVE STEM (6) of
DIVERTER (9). Secure DIVERTER
HANDLE (5) with SCREW (7). Thread
HANDLE CAP (8) onto DIVERTER
HANDLE (5).
For Lever Handles:
Install FRICTION
WASHER (1) onto base of LEVER
HANDLE (2). Turn VALVE to off
position and align LEVER HANDLE (2)
as shown. Install LEVER HANDLE
(2) onto VALVE STEM (3) and tighten
SET SCREW (4) with HEX WRENCH
supplied.
JAD
O
JAD
O
1
Apply putty to the underside of SPRAY BODY
FLANGE (3) and install SPRAY BODY (3) into
spray hole of Bidet.
From underside of Bidet install RUBBER WASHER (4),
FIBER WASHER (5) and LOCKNUT (6) onto shank of SPRAY
BODY (3). Tighten LOCKNUT (6) to make water tight seal.
4
8
5
6
7
7
Connect water supplies to FAUCET (1) with
1/2" IPS FLEXIBLE SUPPLIES (2) or 3/8"
O.D. BULL-NOSE RISERS (3). Use adjustable
wrench to tighten connections. Do not over
tighten. Be careful not to kink copper supply
when bending. Use tubing cutter to cut to
proper length.
Supply connections are made after bidet
has bee installed.
3
2
HOT
HOT
COLD
FRONT
COLD
FERRULE
COUPLING
NUT
1
NOTE: FLEXIBLE SUPPLIES ARE NOT INCLUDED
AND HAVE TO BE PURCHASED SEPARATELY.
BIDET
MOUNTING
SURFACE
Remove LIFT ROD NUT (1), METAL WASHER (2) and
RUBBER SEAL WASHER (3) from LIFT ROD GUIDE (4).
Drop LIFT ROD GUIDE (4) into rear hole of bidet.
From below install RUBBER SEAL WASHER (3), METAL
WASHER (2) and secure guide assembly with LIFT ROD NUT (1).
LIFT ROD GUIDE INSTALLATION
WATER SUPPLY CONNECTIONS
2-7/16" D.
3"
2-7/16" D.
APPLY SEALANT
OR TEFLON TAPE
4
A FOAM SEAL (1) is installed on underside of FLANGE (2). (Plumbers
Putty may be used in place of FOAM SEAL (1) if desired.)
Apply sealant or Teflon tape to threads of TAILPIECE (10) and
thread into DRAIN BODY (7) making a water tight seal.
Drop FLANGE (2) into LAVATORY DRAIN (3). From below assemble
RUBBER GASKET (4), PLASTIC WASHER (5) and LOCK NUT (6) onto
DRAIN FLANGE (2). Do not tighten fully.
INSTALL POP-UP DRAIN
FIG. 4a
FIG. 4b
FIG. 4c
FIG. 4c
FIG. 4a
FIG. 4b
1
4
3
2
5
6
7
8
6
9
2
Adjust STOPPER (13) height by repositioning POP-UP ROD (16) in SWIVEL (15)
and tightening SET SCREW (18).
Assemble POP-UP SWIVEL (15) to PIVOT ROD (11) but do not tighten.
Drop POP-UP ROD (16) through other hole in POP-UP SWIVEL (15) and
tighten SET SCREW (17)
Assemble PIVOT ROD (11), and PIVOT NUT (12) as shown. Install CONCAVE
WASHER (19) into PIVOT ROD OPENING (9) if not preinstalled. Hand tighten
PIVOT NUT (12). Drop STOPPER (13) into drain.
(
To vandal proof drain rotate STOPPER (13) so PIVOT ROD (11) goes
through EYE (14) of STOPPER (13)
. Make connection to "P" TRAP.
Inspect inside DRAIN BODY (7) that SEAL (8) is installed. Thread
DRAIN BODY (7) tight against FLANGE (2) to make a water tight seal.
10
9
7
6
12
19
16
15
17
18
2
10
14
13
11
The PIVOT ROD OPENING (9) in DRAIN BODY (7) should face the rear
of the lavatory. Tighten LOCK NUT (6) on FLANGE (2) to make a water
tight connection with channel locks. Do not over tighten.
1-1/4" O.D.
JADO
JAD
O
1
Turn off hot and cold water
supplies before beginning.
CAUTION
2
FRONT
4
1
5
19
18
17
10
13
6
7
8
9
14
15
16
11
12
INSTALL TRANSFER VALVE
2
INSTALL CONTROL VALVES
Apply sealant or Teflon tape to threads of SPRAY ELL (1) and
install into TRANSFER VALVE (2).
Note: Arrow on SPRAY
ELL (1) points down, see illustration.
Install "Y" HOSE ADAPTER (3) with SEAL (4) to bottom nipple of
TRANSFER VALVE (2) and tighten to make a water tight seal.
Install LOWER CONE SEAL (5) onto TRANSFER VALVE (2) and
insert TRANSFER VALVE (2) from under side of Bidet into the
center forward hole.
Install UPPER CONE SEAL (6), FRICTION WASHER (7) and
MOUNTING NUT (8) onto TRANSFER VALVE (2).
Tighten MOUNTING NUT (8) to secure the TRANSFER VALVE (2)
and make a water tight seal.
Thread TRANSFER VALVE ESCUTCHEON (9) onto MOUNTING
NUT (8) until snug against bidet ledge.
COLD
HOT
BIDET
LEDGE
APPLY SEALANT
OR TEFLON TAPE
10˚
10˚
The HANDLES and HANDLE BASES are installed on VALVE BODIES (10) and
must be removed to install VALVE BODIES (10) from under bidet mounting surface.
To remove LEVER HANDLES (11); loosen SET SCREW (12) with Hex Wrench
supplied with faucet. Pull LEVER HANDLE (11) off and unthread HANDLE BASE (13)
from VALVE BODY (10). Remove ESCUTCHEON (14). Unthread MOUNTING RING
(15) and remove STOP WASHER (16).
Install STOP WASHER (16) onto VALVE BODY (10). Thread MOUNTING RING (15) snug against STOP WASHER (16). Place
ESCUTCHEON (14) onto MOUNTING RING (15). Thread HANDLE BASE (13) until snug against ESCUTCHEON (14). Set
VALVE BODIES (3) so that their outlets are facing toward TRANSFER VALVE (2) and then tighten LOCKNUT (17) using wrench.
Thread LOCKNUT (17) to bottom of VALVE BODY (10). Make sure FIBER
WASHER (18) and RUBBER WASHER (19) are installed. Insert VALVE BODY (10)
through mounting hole from underside of bidet mounting surface.
Note: VALVE BODY marked Hot is installed in the left Mtg. hole,
VALVE BODY marked Cold in the right when facing front of fitting.
Maximum mounting thickness is 1-1/4".
O-RING
