background image

Tools for high speed cutting

Item no. 10202024, Revision 02

26 ( 36 )

11

Tools for high speed cutting

DANGER: Due to flying parts.

If the wrong direction of rotation is used, the tool is damaged when load is
applied. The centrifugal forces cause the broken part to be flung out.

u

Only use tools with the correct direction of rotation for the HF spindle.

DANGER: Due to flying parts.

If  the  speed  is  selected  incorrectly,  the  HF  spindle  or  the  tool  may  be  de-
stroyed and their fragments may be flung out.

u

Note the maximum speed for the selected tool.

u

Note the maximum speed for the HF spindle.

u

Always select the lowest specified speed for machining.

Ü

Only use tools that are technically sound.

Ü

Only use tools with a tool shank diameter that corresponds to the inner di-
ameter of the collet. For example, do not use shanks with a diameter of 3
mm in collets for 1/8” (=3.175 mm).

Ä

Also see the Technical Specifications

 [

}

 12]

 section

Ü

Only use tool shanks with a diameter tolerance of h6.

Ü

Do not use tool shanks with a clamping surface (e.g. Weldon).

Ü

Only use a balanced tool.

Ä

DIN ISO 1940, balance grade 2,5 .

Summary of Contents for Z62-M260.23 S5





































Reviews: