Xonic
®
100 Series
Jain Technology
Tel. 82-2-856-4114 Fax. 82-2-856-9503
24
4.4 Install
–
Path Angle
Input the install angle for each path. The angle between path length and the
transducers. Refer to below figure for Path Angle.
4.5 Install
–
Path Height OPT
In some cases, there might have rapids to cause the fluctuating flow rate which would
affect the measurement. Hence, this function was created to increase the measuring
range of each path.
4.6 Install
–
Auto Install
Caution) We suggest user to use 4.7 Reserve Installation for a better performance.
4.7 Install
–
Reserve Install
The software will run the installation automatically once the level reaches the
programmed height of each path. There are several messages the menu may display.
User should review below carefully before setup.
Caution) User should introduce the parameters of the selecting path before enabling
this function.
INSTALL
1 . SENSOR TYPE
2 . PATH HEIGHT
3 . PATH LENGTH
4 . PATH ANGLE
5 . PATH HEIGHT OPT
6 . AUTO INSTALL
7 . RESERVE INSTALL
8 . INSTALL INFO.
9 . ACTUAL ZERO
0 . SAMPLING CLK
60. 000
PATH ANGLE
UNIT : Degree
INSTALL
1 . SENSOR TYPE
2 . PATH HEIGHT
3 . PATH LENGTH
4 . PATH ANGLE
5 . PATH HEIGHT OPT
6 . AUTO INSTALL
7 . RESERVE INSTALL
8 . INSTALL INFO.
9 . ACTUAL ZERO
0 . SAMPLING CLK
150. 000
PATH HEIGHT OPT
UNIT : mm
INSTALL
1 . SENSOR TYPE
2 . PATH HEIGHT
3 . PATH LENGTH
4 . PATH ANGLE
5 . PATH HEIGHT OPT
6 . AUTO INSTALL
7 . RESERVE INSTALL
8 . INSTALL INFO.
9 . ACTUAL ZERO
0 . SAMPLING CLK
1 . NO
2 . YES
AUTO INSTALL
INSTALL
1 . SENSOR TYPE
2 . PATH HEIGHT
3 . PATH LENGTH
4 . PATH ANGLE
5 . PATH HEIGHT OPT
6 . AUTO INSTALL
7 . RESERVE INSTALL
8 . INSTALL INFO.
9 . ACTUAL ZERO
0 . SAMPLING CLK
1 . SET
2 . CLEAR
RESERVE INSTALL
Press [
MENU
] – 4. INSTALL –
4.PATH ANGLE
Press [
MENU
] – 4.INSTALL –
5.PATH HEIGHT OPT
Press [
MENU
] – 4.INSTALL –
6.AUTO INSTALL
Press [
MENU
] – 4.INSTALL –
7.RESERVE INSTALL
▪
Set – display
“Reserved”
➢
Enable.
➢
The software will do auto installation when
the level is over the path height
.
▪
Clear – display
“Cleared”
➢
Disable.
▪
- display
“Installed”
➢
The system is already installed.
Summary of Contents for Xonic 100 Series
