Xonic
®
100 Series
Jain Technology
Tel. 82-2-856-4114 Fax. 82-2-856-9503
27
Setting Operation
–
Operating Condition
5. Operate -
Before installing the transducer, set the operating condition in the main menu to
allow measurements.
Caution) The measurement might have some errors without these settings.
5.1 Operate –
Upper Flow Limit
Set the MAXIMUM measuring range of the flow so the software will measure the
flow when not exceeds the limited flow rate.
5.2 Operate –
Lower Flow Limit
Set the MINIMUM measuring range of the flow so that measuring rate will not lower
than the limited flow rate.
5.3 Operate –
Dead Level
Dead Level, so called “Blanking Level”. In some cases, flow rate may be disregard
due to small flow in the big channel. Therefore, user can perform the function, so the
flowmeter can be set to ignore a level of the channel bottom to aviod false echoes
from obstructions.
MAIN MENU
1 .
GENERAL
2 .
PATH SELECT
3 .
CH SETUP
4 .
INSTALL [1]
5 .
OPERATE
6 .
FLOW
7 .
IN/OUTPUT
8 .
DATALOG
9 .
DIAG [1]
OPERATE
1 .
UPPER FLOW LIMIT
2 .
LOWER FLOW LIMIT
3 .
DEAD LEVEL
4 .
DEAD ZONE
5 .
FLOW AVERAGE TIME
6 .
TOTAL FLOW SET
7 .
ALARM
8 .
CALIBRATION
9 .
ENABLE AGC
0 .
DAMPING
OPERATE
1 .
UPPER FLOW LIMIT
2 .
LOWER FLOW LIMIT
3 .
DEAD LEVEL
4 .
DEAD ZONE
5 .
FLOW AVERAGE TIME
6 .
TOTAL FLOW SET
7 .
ALARM
8 .
CALIBRATION
9 .
ENABLE AGC
0 .
DAMPING
UPPER FLOW LIMIT
Unit : m³/hour
20000.160
OPERATE
1 .
UPPER FLOW LIMIT
2 .
LOWER FLOW LIMIT
3 .
DEAD LEVEL
4 .
DEAD ZONE
5 .
FLOW AVERAGE TIME
6 .
TOTAL FLOW SET
7 .
ALARM
8 .
CALIBRATION
9 .
ENABLE AGC
0 .
DAMPING
- 20000. 160
Unit : m³/hour
LOWER FLOW LIMIT
OPERATE
1 .
UPPER FLOW LIMIT
2 .
LOWER FLOW LIMIT
3 .
DEAD LEVEL
4 .
DEAD ZONE
5 .
FLOW AVERAGE TIME
6 .
TOTAL FLOW SET
7 .
ALARM
8 .
CALIBRATION
9 .
ENABLE AGC
0 .
DAMPING
DEAD LEVEL
UNIT: mm
0. 000
Press [
MENU
] –
5.OPERATE
Press [
MENU
] – 5.OPERATE –
1.UPPER FLOW
LIMIT
Press [
MENU
] – 5.OPERATE
–
3.DEAD
LEVEL
Press [
MENU
] – 5.OPERATE –
2.LOWER
FLOW LIMIT
Summary of Contents for Xonic 100 Series
