background image

4

INSTALLATION

Recuperator

CAUTION

  Do not install the unit, remote controller and cable within approximately 3 meters

    from strong electromagnetic wave radiators.

WARNING

 •

 Do not perform installation work and electrical wiring connection without referring to 

   the Installation and Operational Manual.
 

 Check that the ground wire is securely connected.

 

 Connect a fuse of specified capacity.

bolt (provided by user)

Duct

Elbow

(To prevent rain 

water from

duct system)

entering into the 

EA

(exhaust air

SA

(Supply

air)

RA

(Return

air)

OA

(outside air

Maintenance

cover

Fresh air

 air

Mounting the Appliance

JRH72N series appliances can directly be mounted on a vibration-free solid wall with the

suspension parts supplied for installation purpose. The screws must be applied in a torque 

enough to secure a rigid connection. The other part is mounted to the wall and used as a

hanger to fix the unit. Following aspects must be considered during mounting of the unit.

1 The appliance must be mounted level.

2 The installation space must be freezing free.

 

Checking Product Received

After receiving the product, inspect for any shipping damage. Claims for damage, either

apparent or concealed, should be files immediately with the shipping company.

Check for the model number and electrical properties like power supply, voltage and frequency

whether they fit your demand or not.

The installation and operation of the unit must be done as explained in this manual; the

utilization of the unit other than those indicated in these instructions is not recommended.

Please contact your local agent for any discrepancy.

Our liability shall not cover any defects arose from the alterations performed by a customer

without our written approval.

Summary of Contents for JRH72N Series















Reviews: