background image

5

Make sure the alignment of ribs on the W5; press the ribs into 

its relative slots on the MW5. Drop instant glue to secure them 

in place.

Please check if there is any joint places need to be secured by 

instant glue. Apply some UHU glue on the joint places of leading 

edge (dowel) and ribs. Wipe off the excess glue. 

Use sanding paper to trim the uneven surface, wing tips and rear 

edge; wait for apply films.

Place MW15 and MW16 on the working table. MW16 will be ap

-

plied  film  on  one  side.  MW15  won‘t  need  any  film.  Don‘t  glue 

MW15 and MW16 to the bottom wing right now.

BOTTOM MAIN WING ASSEMBLY

Place the DW7 (4 pieces) and DW8 (2 pieces) on the working 

table as the picture shown.

Use glue to secure DW7 on both sides of DW8. Make sure the 

alignment of the edges and use clip to hold the combination tem-
porary until the glue is dried enough. Drop some instant glue on
the edges. 

Top view of the DW7 combinations. There is one small hole on 

the top.

LANDING GEAR SUB WING ASSEMBLY

Place the following parts on the working table in order:

DW1  leading edge

DW7   (2 pieces)ribs

DW6   (2 pieces)ribs

DW5   (3 pieces)ribs

DW2.  middle edge

DW3  secondary edge

DW4  rear edge

Try to fit ribs to the DW2 and DW3.Don‘t use any glue now.

Try to fit 2 pieces of DW7 on both side of sub wing. Please note 

the hole on DW7 must face the upward.

Place MW13 and MW14 on the working table.

Fit the MW13 to the main wing as the wing tip. Fit the MW14 into 

the slot on the middle edge between the main wing and MW13. 

The angle between the MW14 and MW13 must be 90 degree. 

Drop some instant glue to secure the MW14 in place.

Summary of Contents for Fokker DVII





























Reviews: