APPENDIX A
J2001T PELLET STOVE
Standard Shroud Kit#J2001TS Installation Instructions
Appendix A-1
1998-2006 Edition
Parts List
1. Shroud Top #C187T
2. Shroud Left Leg #C187L
3. Shroud Right Leg #C187R
4. Hopper Opening Sealer #C373. Included w/stove.
5. Five (5) #8 x 1/2" Hex Head Teck Screws
6. Eight (8) #8 x 1/2" Phil. Pan Head Sheet Metal or Teck Screws.
Tools Required
1. Electric Screw Gun
2. Standard Phillips Screwdriver bit
3. 1/4" Hex Head driver bit
4. 5/16" Open End Wrench
1. Locate the Hopper Opening Sealer (see Figure 1) inside the firebox or inside the hopper. Remove this part.
Unwrap and discard the wrapping material.
2. Identify the steel parts listed above according to Figure 1.
3. Lift the Shroud Top Opening Door [which is hinged to the stove top] and lay it over the stove top trivet so that
the black latch knob is resting on the trivet.
4. Look at Figure 2. Identify the two Hex Head Screws that are attached to the downward bend on the rear of the
stove top. Note that these screws are not tightened completely.
5. See Figure 2 and 3. Slide the Shroud Top behind the stove top while aligning the open slots in the Shroud Top
with the two Hex Head Screws on the Stove top back. Slide shroud top slots between the hex heads and the
stove top. Please note that the shroud top must sit behind the stove top but in front of the outward bends at the
rear end of the stove side panels. The shroud top must be located between the stove top and the outward bend
on the stove side panel.
6. Close the Shroud Top Opening Lid onto the Shroud Top and latch it. Tighten the two hex head screws on the
stove top back using a 5/16" open end wrench so that the shroud top stays in place. Try opening the Shroud Top
Opening Door by turning the latch knob. If the operation is smooth, tighten the two hex head screws securely. If
the operation is not smooth, lift the shroud top upwards 1/16" and tighten the two hex head screws.
7. Align screw hole # [H1] on the side panel with screw hole #[H1] in the shroud top face as shown in Figure 2.
Drive one #8 x 1/2" Phillips head sheet metal screw or Teck screw [4] through these holes. Tighten.
8. Using a 5/16" Open End Wrench, tighten the two hex head screws on the rear of the stove top so as to secure
the shroud top to the stove top.
9. Mount the Control Cover Plate Assembly onto the right shroud leg as shown in Figure 3. Note that when
mounting the Controls Cover Plate Assembly, do not disconnect any of the wires attached to its back side. Slide
the entire control cover plate assembly [with wires attached] through the rectangular hole and then proceed with
mounting the brass screws and nuts.
10. To mount the Shroud Legs onto the stove, align screw hole #[H2] on the shroud leg [3] with screw hole
#[H2] in the shroud top “Z” bend. See Figure 4. Drive one #8 x 1/2" Phillips head sheet metal screw or Teck screw
[4] through these screw holes.
11. Align screw hole #[H3] located at the bottom of the shroud leg with screw hole #[H3] at the bottom of the
outward bend on the stove side panel. Drive a #8 x 1/2" Phillips head sheet metal screw or Teck screw through
these holes.
12. Align and drive one #8 x 1/2" Phillips head sheet metal screw or Teck screw through the remaining holes
#[H4] on the mitered edge along the top edge of the shroud leg.
13. Center the Hopper Opening Sealer (see Figure 5) on the back side of the shroud top. Push the Hopper
opening Sealer against the Shroud top.
14. While holding the shroud top vertically straight, drive one #8 x 1/2” Hex Head Teck Screw through each screw
hole (in the Hopper Opening Sealer) into the hopper top.
15. Seal the joints between the Hopper Opening Sealer and the Shroud Top and Hopper Top with black silicone
or aluminum foil tape.
Summary of Contents for J1000B
